NetPA 1001-70V AT
EUR
1260.00
€ 1260.00
Hersteller
Extron
Art.Nr.
60-1501-01
EAN
60-1501-01
Gewicht
2 kg
Produktbeschreibung
Hauptmerkmale
- Empfängt Eingangssignale über das Dante®-Netzwerk
- 100 W eff. Ausgangsleistung:
1 x 100 W bei 70 V - ENERGY STAR®-konformer Verstärker
- Dante-Audionetzwerke bieten zahlreiche Erweiterungsmöglichkeiten
- Dante-Audio zu Linepegel-Ausgang
- Professionelles Signal-Rausch-Verhältnis und Klirrfaktor
Modell | Beschreibung der Version | Teilenummer | |
---|---|---|---|
NetPA 1001-70V AT | 70 V Mono-Verstärker mit Dante - 100 W | 60-1501-01 |
Technische Daten
Technische Daten
-
NetPA Series Audio Crosstalk >75 dB @ 1 kHz Audio input Number/signal type NetPA 502 AT 1 stereo or 2 mono NetPA 1001-70V AT 1 mono Connectors 1 RJ-45 Maximum level 0 dBFS (digital) Audio processing D/A conversion 24 bit, selectable sampling rate AT ports — audio transport Transmission type Dante Connectivity 1 RJ-45 connector, 1-port 100 Mbps to Dante interface Inputs NetPA 502 AT 2 channels Rx NetPA 1001-70V AT 1 channel Rx Audio format 24-bit uncompressed, selectable at 44.1, 48, 88.2, and 96 kHz sampling rate Latency Deterministic, based on user selection: 2.0 ms (default), 5.0 ms Audio line output Number/signal type NetPA 502 AT 2 channels, balanced/unbalanced NetPA 1001-70V AT 1 channel, balanced/unbalanced Connectors NetPA 502 AT (1) 3.5 mm captive screw connector, 6 pole NetPA 1001-70V AT (1) 3.5 mm captive screw connector, 3 pole Impedance 50 ohms unbalanced, 100 ohms balanced Maximum level (at 0 dBFS digital input) >+15 dBu balanced; +9 dBu unbalanced Frequency response 20 Hz to 20 kHz, ±1 dB THD + Noise 0.03% @ 1 kHz at nominal level,
0.3% @ 20 kHz at nominal levelS/N >90 dB, at maximum output (unweighted) NOTE 0 dBu = 0.775 Vrms, 0 dBV = 1 Vrms, 0 dBV ? 2 dBu Audio speaker output Number/signal type NetPA 502 AT 2 channels, 4 or 8 ohms NetPA 1001-70V AT 1 channel, 70 V Connectors NetPA 502 AT (1) 5.08 mm screw lock captive screw connector, 4 pole NetPA 1001-70V AT (1) 5.08 mm screw lock captive screw connector, 2 pole NOTE These connectors accept wires of 22 AWG to 12 AWG. Load impedance NetPA 502 AT 4 ohms minimum NetPA 1001-70V AT 50 ohms minimum Amplifier type Class D Output power NetPA 502 AT 50 watts rms per channel, 4 ohms, 1 kHz, 0.1% THD
25 watts rms per channel, 8 ohms, 1 kHz, 0.1% THDNetPA 1001-70V AT 100 watts rms, 70 V, 1 kHz, 0.1% THD Frequency response NetPA 502 AT 20 Hz to 20 kHz, +1/-3 dB @ 1 watt NetPA 1001-70V AT 20 Hz to 20 kHz, +1/-3 dB @ 1 watt THD + Noise <0.1% @ 1 kHz, 3 dB below clipping S/N >90 dB, 20 Hz - 20 kHz, unweighted High pass filter NetPA 1001-70V AT 80 Hz, 12 dB per octave rolloff for 70 V line output (switch selectable) Communications — amplifier Control port (1) 3.5 mm captive screw connector, 2 pole Pin configurations Standby power control (contact closure) Pin 1 = standby, pin 2 = Gnd
General Power supply Internal
Input: 100-240 VAC, 50-60 Hz, 0.5 APower consumption and thermal dissipation NetPA 502 AT 115 VAC, 60Hz 230 VAC, 50Hz AC Line
CurrentAC Power
ConsumedThermal
DissipationAC Line
CurrentAC Power
ConsumedThermal
Dissipation/Condition A W W BTU/hr A W W BTU/hr Active (1/8 power), all
channels driven8? 0.3 14.6 8.3 28 0.2 17 10.7 36 4? 0.4 22.3 9.8 33 0.3 24 11.7 40 Quiescent (idle) 0.1 7.4 7.4 25 0.1 9.9 9.9 34 Standby <0.1 <2 <2 <6 <0.1 <2 <2 <6 NetPA 1001-70V AT 115 VAC, 60Hz 230 VAC, 50Hz AC Line
CurrentAC Power
ConsumedThermal
DissipationAC Line
CurrentAC Power
ConsumedThermal
DissipationCondition A W W BTU/hr A W W BTU/hr Active (1/8 power), all
channels driven70 V 0.4 22.7 10.2 35 0.3 24.1 11.6 39 Quiescent (idle) 0.1 7.6 7.6 26 0.1 9.2 9.2 31 Standby <0.1 <2 <2 <6 <0.1 <2 <2 <6 Temperature/humidity Storage: -40 to +158 °F (-40 to +70 °C) / 10% to 90%, noncondensing
Operating: +32 to +104 °F (0 to +40 °C) / 10% to 90%, noncondensingCooling Convection, no vents, with internal heat sink Protection Clip limiting, thermal, short circuit, DC output Indication Limiter/Protect LED indicates the onset of clip limiting, thermal cycling, or short circuit Mounting Rack mount Yes, with optional 1U rack shelf Furniture mount Yes, with optional under-desk mounting kit Enclosure type Metal Enclosure dimensions 1.7" H x 8.7" W x 9.5" D (1U high, half rack wide)
(4.3 cm H x 22.1 cm W x 24.1 cm D)Product weight NetPA 502 AT 2.6 lbs (1.2 kg) NetPA 1001-70V AT 2.6 lbs (1.2 kg) Vibration ISTA 1A in carton (International Safe Transit Association) Regulatory compliance Safety CE, c-UL, UL
Meets UL 60065, IEC 60065, and BSEN 60065 for AV equipment.EMI/EMC CE, C-tick, EN 55103-1, EN 55103-2, FCC Class B, ICES, VCCI Class B Environmental Complies with the appropriate requirements of ENERGY STAR® (ENERGY STAR qualified amplifier), RoHS, WEEE. Product warranty 3 years parts and labor Everlast power supply warranty 7 years parts and labor NOTE All nominal levels are at ±10%. NOTE Specifications are subject to change without notice. (081717-D7) Versand-Abmessung und -Gewicht Teilenummer Höhe Breite Tiefe Gewicht 60-1501-01 11,4 cm 34,9 cm 35,6 cm 2,27 kg