FOXBOX Tx DVI Plus

Technische Daten

FOXBOX Tx-Rx DVI Plus
NOTE     The FOXBOX Tx DVI Plus transmitter is compatible only with the following receivers: FOXBOX Rx DVI Plus, PowerCage FOX Rx DVI Plus board, FOXBOX Rx HDMI, PowerCage FOX Rx HDMI board, FOXBOX SR HDMI, and PowerCage FOX SR HDMI board.
NOTE     The analog audio signals are digitized in the transmitter, sent through the fiber cable, and converted back to analog audio in the receiver.
NOTE     This transmitter and receiver are class 1 laser products. They meet the safety regulations of IEC-60825.
Optical fiber interconnection between transmitter and receiver
Number/type	1 or 2 fiber optic
NOTE     Only one fiber is required to transmit video, audio, and unidirectional data. A second fiber is required to transmit return data for bidirectional control/communication.
Connectors	2 LC connectors
Operating distance
Singlemode	30 km (18.75 miles) with singlemode (SM) cables with SM units
Multimode	300 m (985') with 62.5 µm OM1 multimode (MM) cables with MM units 1 km (3280') with 50 µm OM2 multimode (MM) cables with MM units 2 km (6561') with 50 µm OM3/OM4 2000 MHz bandwidth laser optimized multimode cable with a MM units
NOTE     Operating distance is approximate. These are typical maximum distances that may vary depending on factors such as fiber type, fiber bandwidth, connector splicing, losses, modal or chromatic dispersion, environmental factors, and kinks.
Nominal peak wavelength	850 nm for MM, 1310 nm for SM
Data rate	4.25 Gbps
Transmission power	-5 dBm, typical
Maximum receiver sensitivity
Singlemode	-18 dBm, typical
Multimode	-12 dBm, typical
Optical loss budget
Singlemode	13 dB, maximum
Multimode	7 dB, maximum
Video
NOTE     *Appropriate DVI-D to HDMI cables or adapters are required for HDMI signal input/output. The FOXBOX DVI Plus Series can be used to distribute HDMI signals if you use a DVI-to-HDMI adapter. However, when using HDMI signals, these units do not transmit audio and CEC signals. The FOXBOX DVI Plus does not support transmission of DVI signals with High-bandwidth Digital Content Protection (HDCP).
Resolution range	Up to 1920x1200 or 1080p @ 60 Hz pixel for pixel
Formats	RGB and YCbCr digital video
Standards	DVI 1.0, HDMI
Video input
Number/signal type	1 single link DVI-D (or HDMI*)
Connectors	1 female DVI-I
Video output
Number/signal type	1 single link DVI-D (or HDMI*)
Connectors	1 female DVI-I
Nominal level	0.8 Vp-p
Video delay	1-2 frames
Audio
Gain
Range	Adjustable, -18 dB to +10 dB
Default	Unbalanced output: 0 dB
Frequency response	20 Hz to 20 kHz, ±0.5 dB
THD + Noise	0.10% @ 1 kHz at nominal level
S/N	>80 dB at maximum output (unweighted)
Audio bits per sample	18 bits per channel, 2 channels (L, R)
Sampling rate	48 kHz
Audio input — transmitters
Number/signal type	1 unbalanced stereo or 2 unbalanced mono
Connectors	(1) 3.5 mm mini stereo jack
Impedance	18k ohms unbalanced, DC coupled
Nominal level	-10 dBV (316 mVrms)
Maximum level	+8.9 dBV, (unbalanced) at 1% THD+N
NOTE     0 dBu = 0.775 Vrms, 0 dBV = 1 Vrms, 0 dBV ? 2 dBu
Audio output — receivers
Number/signal type	1 unbalanced stereo or 2 unbalanced mono
Connectors	(1) 3.5 mm mini stereo jack
Impedance	50 ohms unbalanced
Nominal level	-10 dBV (316 mVrms)
Maximum level (Hi-Z)	+7.6 dBu, unbalanced at 1% THD+N
Maximum level (600 ohm)	>+6.3 dBu, unbalanced at 1% THD+N
Audio delay	1.5 frames
Control/remote
Serial control ports on each unit (transmitter and receiver)
Control	1 RS-232, 2.5 mm mini stereo jack (front panel)
Pass-through	1 RS-232, 3.5 mm captive screw connector, 5-pole (3 pins are used) (rear panel)
Baud rate and protocol
Control	9600 baud, 8 data bits, 1 stop bit, no parity
Pass-through	9600 to 115,200 baud
Serial control pin configuration	Mini stereo jack: tip = Tx, ring = Rx, sleeve = GND
Program control	Extron control/configuration program for Windows® Extron Simple Instruction Set (SIS™)
General
Power supply	External Input: 100-240 VAC, 50-60 Hz Output: 12 VDC, 1.5 A, 18 watts
Power input requirements	12 VDC, 0.6 A
Temperature/humidity	Storage: -40 to +158 °F (-40 to +70 °C) / 10% to 90%, noncondensing Operating: +32 to +122 °F (0 to +50 °C) / 10% to 90%, noncondensing
Cooling	Convection, vents on top and side panels
Thermal dissipation
Transmitter	4.0 BTU/hr
Receiver	3.9 BTU/hr
Mounting
Rack mount	Yes, with optional rack shelf
Furniture mount	Yes, with optional under desk mounting kit
Enclosure type	Metal
Enclosure dimensions	1.0" H x 4.3" W x 6.0" D (quarter rack wide) (2.5 cm H x 10.9 cm W x 15.2 cm D) (Depth excludes connectors.)
Product weight	0.7 lbs (0.3 kg) per unit, 1.4 lbs (0.6 kg) per pair
Regulatory compliance	CE, c-UL UL, CE, C-tick, FCC Class A, ICES, VCCI, Complies with the appropriate requirements of RoHS, WEEE
Product warranty	3 years parts and labor
Everlast power supply warranty	7 years parts and labor
NOTE     All nominal levels are at ±10%.
NOTE     Specifications are subject to change without notice.
(4399-101518-D10)

Versand-Abmessung und -Gewicht
Teilenummer	Höhe	Breite	Tiefe	Gewicht
60-1060-11	6,4 cm	31,3 cm	22,2 cm	1,04 kg
60-1060-12	6,4 cm	31,3 cm	22,2 cm	1,04 kg