PowerCage FOX Rx DVI Plus

Technische Daten

PowerCage™ FOX Rx DVI Plus
NOTE     The PowerCage FOX Rx DVI Plus is not compatible with the FOX 3G HD-SDI, FOX 3G DVC, or FOX AV models.
NOTE     The PowerCage FOX Rx DVI Plus board is available in singlemode or multimode version.
NOTE     The PowerCage FOX Rx DVI Plus board is a class 1 laser product. It meets the safety regulations of IEC-60825.
Optical fiber interconnection between transmitter and receiver
Number/type	1 singlemode or 1 multimode fiber optic input and output per board
NOTE     Only one fiber is required to transmit video, audio, and unidirectional data. A second fiber is required to transmit HDMI video with HDCP content or return data for bidirectional control and communication.
Connectors	2 bidirectional LC connectors per FOX board
Operating distance
Singlemode	30 km (18.75 miles) with singlemode (SM) cables with a SM board
Multimode	300 m (985') with 62.5 µm OM1 multimode (MM) cable and a MM board 1 km (3280') with 50 µm OM2 multimode (MM) cable and a MM board 2 km (6561') with 50 µm OM3/OM4 2000 MHz bandwidth laser optimized MM cable and a MM board
NOTE     Operating distance is approximate. These are typical distances. The maximum distance may be greater than these typical numbers depending on factors such as fiber type, fiber bandwidth, connector splicing, losses, modal or chromatic dispersion, environmental factors, and kinks.
Nominal peak wavelength	850 nm for multimode (MM), 1310 nm for singlemode (SM)
Transmission power, singlemode or multimode	-5 dBm, typical
Maximum receiver sensitivity
Singlemode	-18 dBm, typical
Multimode	-12 dBm, typical
Optical loss budget
Singlemode	13 dB, maximum
Multimode	7 dB, maximum
Maximum channel data rate	4.25 Gbps
Video
Resolution range	640x480 up to 1920x1200 @ 60Hz, including 480p, 576p, 720p, 1080i, 1080p @ 60Hz, sampled pixel for pixel; higher resolution 2K (2048x1080) @ 60 Hz, undersampled
Format	RGB
Standards	DVI 1.0, HDMI
Video output
Number/signal type	1 single link DVI-D (or HDMI*)
Connector	1 female DVI-I
Nominal level	0.8 Vp-p
Video delay	1-2 frames
Audio
NOTE     On the PowerCage FOX Rx DVI Plus board, the analog audio signals are digitized in the transmitter, sent through the fiber cable, and converted back to analog audio in the receiver.
Gain
Range	Adjustable, -18 dB to +10 dB
Default	Unbalanced output: -6 dB; balanced output: 0 dB
Frequency response	20 Hz to 20 kHz, ±0.5 dB
THD + Noise	0.10% @ 1 kHz at nominal level
S/N	>80 dB at maximum output (unweighted)
CMRR	65 dB @ 20 Hz to 20 kHz
Audio bits per sample	18 bits per channel, 2 channels (L, R)
Sampling rate	48 kHz
Audio output
Number/signal type	1 stereo, balanced/unbalanced or 2 mono, balanced/unbalanced
Connectors	(1) 3.5 mm captive screw connector, 5 pole
Impedance	50 ohms unbalanced, 100 ohms balanced
Nominal level	+4 dBu (1.23 Vrms), -10 dBV (316 mVrms)
Maximum level (Hi-Z)	+7.6 dBu, unbalanced at 1% THD+N
Maximum level (600 ohm)	>+6.3 dBu, unbalanced at 1% THD+N
Audio delay	1.5 frames
Control/remote
Serial control ports
Control	1 bidirectional RS-232, 3.5 mm captive screw connector, 5 pole (uses 3 poles; shared with the alarm port)
Pass-through	1 RS-232, 3.5 mm captive screw connector, 5 pole (3 pins are used, "RS-232 Over Fiber")
Baud rate and protocol
Control	9600 baud, 8 data bits, 1 stop bit, no parity
Pass-through	9600 to 115,200 baud
Serial control pin configurations
Captive screw connector	1 = Tx, 2 = Rx, 3 = GND
Mini stereo jack	RS-232: tip = Tx, ring = Rx, sleeve = GND
Program control	Extron control/configuration program for Windows® Extron Simple Instruction Set (SIS™)
General
Power	Supplied by a PowerCage 1600 enclosure
Power consumption	6.18 watts
Power input requirements	12 VDC, 1.0 A, supplied by the PowerCage enclosure
Temperature/humidity	Storage: -40 to +158 °F (-40 to +70 °C) / 10% to 90%, noncondensing Operating: +32 to +122 °F (0 to +50 °C) / 10% to 90%, noncondensing
Cooling	Enclosure: fans, front to back Boards: convection, within the PowerCage enclosure
Thermal dissipation	27.6 BTU/hr
Dimensions	Each board fits a double slot opening in a PowerCage enclosure.
Product weight	1.1 lbs (0.5 kg)
Shipping weight	2 lbs (1 kg)
Vibration	ISTA 1A in carton (International Safe Transit Association)
Regulatory compliance
Safety	CE, c-UL, UL
EMI/EMC	CE, C-tick, FCC Class A, ICES, VCCI
Environmental	Complies with the appropriate requirements of RoHS, WEEE.
Product warranty	3 years parts and labor
NOTE     All nominal levels are at ±10%.
NOTE     Specifications are subject to change without notice.
(8.1-121114-D3)

Versand-Abmessung und -Gewicht
Teilenummer	Höhe	Breite	Tiefe	Gewicht
70-873-21	6,7 cm	22,9 cm	34,0 cm	0,73 kg
70-873-22	6,7 cm	22,9 cm	34,0 cm	0,73 kg