DTP T DSW 4K 233
EUR
1536.00
€ 1536.00
Hersteller
Extron
Art.Nr.
60-1487-12
EAN
60-1487-12
Gewicht
1 kg
Produktbeschreibung
Hauptmerkmale
- Überträgt DisplayPort-, HDMI- oder VGA- sowie Steuerungs- und analoge Audiosignale bis zu 70 m über ein geschirmtes CATx-Kabel
- Automatische Umschaltung zwischen den Eingängen
- Unterstützt Computer- und Video-Auflösungen bis zu 4K
- Embedding von analogem Stereo-Audio
- Es wird ausdrücklich geschirmtes XTP DTP 24-Twisted Pair-Kabel von Extron für eine optimale Leistung empfohlen
- Kompatibel mit geschirmtem CATx-Twisted Pair-Kabel
Modell | Beschreibung der Version | Teilenummer | |
---|---|---|---|
DTP T DSW 4K 233 | DisplayPort-, HDMI- und VGA-Umschalter – 70 m | 60-1487-12 | |
DTP T DSW 4K 333 | DisplayPort-, HDMI- und VGA-Umschalter – 100 m | 60-1487-52 |
Technische Daten
Technische Daten
-
DTP T DSW 4K Series specification Frame rate 1 24, 25, 30, 502, or 602 fps Chroma sampling 1 4:4:4, 4:2:2, or 4:2:02 Color bit depth 1 8 bits per color Signal type 1 HDMI 1.4 , DisplayPort 1.1a, HDCP 1.4 Max. video data rate 1 HDMI 10.2 Gbps (3.4 Gbps per color) DisplayPort 10.8 Gbps (2.7 Gbps per lane) NOTE 1Subject to the maximum data rate limit. Use our calculator (www.extron.com/4Kdatarate) to determine video parameters supported by this data rate.
2Applicable to HDMI signals only.Video VGA input Gain Unity Bandwidth 170 MHz (-3 dB) Crosstalk -50 dB @ 10 MHz, -30 dB @ 100 MHz HDMI input Maximum data rate 10.2 Gbps (3.4 Gbps per color) Maximum pixel clock 300 MHz Resolution range Up to 2560x1600* @ 60 Hz or 4K (4096x2160) @ 30 Hz,
UHD (3840x2160) @ 30 Hz, 4K/UHD @ 60 Hz with 4:2:0 chroma subsampling
(*Reduced blanking)Formats RGB and YCbCr digital video Standards DVI 1.0, HDMI 1.4, HDCP 1.4, CEA-861E DisplayPort input Maximum data rate 10.8 Gbps (2.7 Gbps per lane) Maximum pixel clock 300 MHz Resolution range Up to 2560x1600* @ 60 Hz or 4K (4096x2160) @ 30 Hz
(*Reduced blanking)Formats RGB and YCbCr digital video Standards DisplayPort 1.1a Video input Number/signal type VGA input 1 VGA-WUXGA RGBHV HDMI input 1 single link HDMI (or DVI-D*) DisplayPort input 1 DisplayPort NOTE *Appropriate HDMI to DVI-D cables or adapters are required for DVI signal input/output. Connectors VGA input 1 female 15-pin HD HDMI input 1 female HDMI, type A DisplayPort input 1 female DisplayPort VGA input Nominal level 1.0 Vp-p Minimum/maximum levels Analog 0.3 V to 1.5 Vp-p with no offset Impedance 75 ohms Horizontal frequency 15 kHz to 145 kHz Vertical frequency 30 Hz to 170 Hz Return loss <-40 dB @ 5 MHz Video output Number/signal type DTP T DSW 4K 233 1 DTP 230 (output) DTP T DSW 4K 333 1 DTP 330 (output) Interconnection between transmitter and receiver Connectors 1 RJ-45 jack Termination standards TIA/EIA T568B DTP signal Signal transmission distance DTP T DSW 4K 233 1080p @ 60 Hz Up to 230' (70 m) using shielded twisted pair (STP) cable or XTP DTP 24 cable 2560x1600 @ 60 Hz Up to 130' (40 m) using STP cable or XTP DTP 24 cable 4K/UHD @ 30 and 60 Hz Up to 130' (40 m) using STP cable or XTP DTP 24 cable DTP T DSW 4K 333 1080p @ 60 Hz Up to 330' (100 m) using shielded twisted pair (STP) cable or XTP DTP 24 cable 2560x1600 @ 60 Hz Up to 330' (100 m) using STP cable or XTP DTP 24 cable 4K/UHD @ 30 and 60 Hz Up to 330' (100 m) using STP cable or XTP DTP 24 cable Cable requirements Solid conductor, 24 AWG or better Cable recommendations 400 MHz bandwidth STP cable NOTE Extron XTP DTP 24 shielded twisted pair cable is strongly recommended for optimal performance. NOTE Output mode signaling:
DTP: HDMI with embedded audio, analog audio, RS-232 and IR, and remote power
HDBaseT: HDMI with embedded audio plus RS-232 and IRSync — VGA Input type RGBHV, bi-level and tri-level sync Input level 1.9 V to 5.0 Vp-p Input impedance 510 ohms Max. input voltage 5.0 Vp-p Audio Frequency response 20 Hz to 20 kHz, ±0.5 dB THD + Noise 0.03% @ 1 kHz at nominal level S/N >90 dB at maximum input (unweighted) Stereo channel separation >80 dB @ 1 kHz Audio input Number/signal type 1 stereo, unbalanced Connectors (2) 3.5 mm stereo jack, 2 channel; tip (L); ring (R); sleeve (Gnd) Impedance >10k ohms, DC coupled Nominal level -10 dBV (316 mVrms) Maximum level +6 dBV, unbalanced NOTE 0 dBu = 0.775 Vrms, 0 dBV = 1 Vrms, 0 dBV ? 2 dBu Control/remote — switcher Serial control port RS-232 via 1 rear panel 3.5 mm, 3-pole captive screw connector Pin configuration 1 = Tx, 2 = Rx, 3 = Gnd Baud rate and protocol 9600 baud rate, 8 data bits, 1 stop bit, no parity Contact closure (1) 3.5 mm, 4-pole captive screw connector Pin configuration Pin 1 = input 1 contact, Pin 2 = input 2 contact, Pin 3 = input 3 contact, Pin 4 = Gnd Tally output (1) 3.5 mm, 4-pole captive screw connector Pin configuration Pin 1 = input 1 tally ground, Pin 2 = input 2 tally ground, Pin 3 = input 3 tally ground, Pin 4 = +5 V USB control port 1 front panel female mini USB B USB standards USB 2.0, low speed Program control Extron Simple Instruction Set (SIS™) Control/remote — external device (RS-232/IR over TP) NOTE Protocol is mirrored between the connected DTP 230 Rx or DTP 330 Rx endpoints and the "Over TP" ports on the
DTP T DSW 4K series. Signals from a control device pass into each "Over TP" port, are embedded with the DTP signal, and sent to the individual DTP 230 Rx or DTP 330 Rx endpoints for control of remote sink or source devices. The "Over TP" ports are simply pass-through connections to DTP endpoints. There is no RS-232 or IR insertion from any
DTP T DSW 4K control port to the "Over TP" ports.Serial control port Bidirectional RS-232 via 1 rear panel 3.5 mm, 5-pole captive screw connector (connector is shared with IR control ports) Baud rate and protocol 300 to 115200 baud, 8 or 7 data bits, 1 or 2 stop bits, non-parity (default), even or odd parity Serial control pin configuration 1 = Tx, 2 = Rx, 3 = Gnd IR pass-through control port 1 bidirectional rear panel 3.5 mm, 5-pole captive screw connector (connector is shared with RS-232 control port) TTL level (0 to 5 V) modulated infrared control from 30 kHz up to 60 kHz IR control pin configuration 3 = Gnd, 4 = IR Tx, 5 = IR Rx General Power supply External
Input: 100-240 VAC, 50-60 Hz
Output: 12 VDC, 2 A, 24 wattsNOTE This product requires a locally connected power supply. It can provide remote DC power to a connected DTP receiver over twisted pair. Power consumption Device DTP T DSW 4K 233 11.4 watts DTP T DSW 4K 333 12.0 watts Device and power supply DTP T DSW 4K 233 14.1 watts DTP T DSW 4K 333 14.7 watts Temperature/humidity Storage: -40 to +158 °F (-40 to +70 °C) / 10% to 90%, noncondensing
Operating: +32 to +122 °F (0 to +50 °C) / 10% to 90%, noncondensingCooling Convection, no vents Thermal dissipation Device DTP T DSW 4K 233 22.7 BTU/hr DTP T DSW 4K 333 24.4 BTU/hr Device and power supply DTP T DSW 4K 233 32.0 BTU/hr DTP T DSW 4K 333 33.6 BTU/hr Rack mount Yes, with optional rack shelf kit Enclosure type Metal Enclosure dimensions 1.0" H x 8.75" W x 6.0" D (1" high, half rack wide)
2.5 cm H x 22.2 cm W x 15.2 cm D (depth excludes connectors)Product weight 1.1 lbs (0.5 kg) Vibration ISTA 1A in carton (International Safe Transit Association) Regulatory compliance Safety CE, c-UL, UL EMI/EMC CE**, C-tick, FCC Class A**, ICES Environmental Complies with the appropriate requirements of RoHS, WEEE NOTE **CE and FCC testing is conducted with STP cable. Product warranty 3 years parts and labor Everlast power supply warranty 7 years parts and labor NOTE All nominal levels are at ±10%. NOTE Specifications are subject to change without notice. NOTE Shipping dimensions and weights are available at http://www.extron.com. (8.1-071116-D3) Versand-Abmessung und -Gewicht Teilenummer Höhe Breite Tiefe Gewicht 60-1487-12 12,1 cm 28,1 cm 24,5 cm 1,32 kg