DTP T DWP 4K 232 D

Technische Daten

DTP T DWP 4K 232 D
specification
Frame rate 1	24, 25, 30, 502, or 602 fps
Chroma sampling 1	4:4:4, 4:2:2, or 4:2:02
Color bit depth 1	8 bits per color
Signal type 1	HDMI 1.4 , DisplayPort 1.1a, HDCP 1.4
Max. video data rate 1
HDMI	10.2 Gbps (3.4 Gbps per color)
DisplayPort	10.8 Gbps (2.7 Gbps per lane)
NOTE     1Subject to the maximum data rate limit. Use our calculator (www.extron.com/4Kdatarate) to determine video parameters supported by this data rate. 2Applicable to HDMI signals only.
Video
HDMI input
Maximum data rate	10.2 Gbps (3.4 Gbps per color)
Maximum pixel clock	300 MHz
Resolution range	Up to 2560x1600* @ 60 Hz or 4K (4096x2160) @ 30 Hz, UHD (3840x2160) @ 30 Hz, 4K/UHD @ 60 Hz with 4:2:0 chroma subsampling (*Reduced blanking)
Formats	RGB and YCbCr digital video
Standards	DVI 1.0, HDMI
DisplayPort input
Maximum data rate	10.8 Gbps (2.7 Gbps per lane)
Maximum pixel clock	300 MHz
Resolution range	Up to 2560x1600* @ 60 Hz or 4K (4096x2160) @ 30 Hz (*Reduced blanking)
Formats	RGB and YCbCr digital video
Standards	DisplayPort 1.1a
Video input
NOTE     *Appropriate HDMI to DVI-D cables or adapters are required for DVI signal input/output.
Number/signal type
HDMI input	1 single link HDMI (or single link DVI-D*) input
DisplayPort input	1 DisplayPort
Connectors
HDMI input	1 female HDMI, type A
DisplayPort input	1 female DisplayPort
Interconnection between transmitter and receiver
Signal type	1 DTP 230 output
Connectors	1 female RJ-45 jack
Termination standards	TIA/EIA T568B
DTP signal
Signal transmission distance
1080p @ 60 Hz	Up to 230' (70 m) using shielded twisted pair (STP) cable or XTP DTP 24 cable
2560x1600 @ 60 Hz	Up to 130' (40 m) using STP cable or XTP DTP 24 cable
4K/UHD @ 30 and 60 Hz	Up to 130' (40 m) using STP cable or XTP DTP 24 cable
Cable requirements	Solid conductor, 24 AWG or better
Cable recommendations	400 MHz bandwidth STP cable
NOTE     Extron XTP DTP 24 shielded twisted pair cable is strongly recommended for optimal performance.
NOTE     Output mode signaling: DTP:             HDMI with embedded audio, analog audio, RS-232 and IR, and remote power HDBaseT:   HDMI with embedded audio plus RS-232 and IR
Audio
Frequency response	20 Hz to 20 kHz, ±0.5 dB
THD + Noise	0.03% @ 1 kHz at nominal level
S/N	>90 dB at maximum input (unweighted)
Stereo channel separation	>80 dB @ 1 kHz
Audio input
Number/signal type	2 stereo, unbalanced
Connectors	(2) 3.5 mm stereo jack, 2 channel; tip (L); ring (R); sleeve (Gnd)
Impedance	>10k ohms, DC coupled
Nominal level	-10 dBV (316 mVrms)
Maximum level	+6 dBu, unbalanced
NOTE     0 dBu = 0.775 Vrms, 0 dBV = 1 Vrms, 0 dBV ? 2 dBu
Control/remote — switcher
Serial control port	RS-232 via 1 rear panel 3.5 mm, 3-pole captive screw connector
Pin configuration	1 = Tx, 2 = Rx, 3 = Gnd
Baud rate and protocol	9600 baud rate, 8 data bits, 1 stop bit, no parity
USB control port	1 front panel female mini USB B
USB standards	USB 2.0, high speed
Program control	Extron Simple Instruction Set (SIS™)
Control/remote — external device (RS-232/IR over TP)
NOTE     Protocol is mirrored between the connected DTP 230 Rx or DTP 330 Rx endpoints and the "Over TP" ports on the DTP T DWP 4K series. Signals from a control device pass into each "Over TP" port, are embedded with the DTP signal, and sent to the individual DTP 230 Rx or DTP 330 Rx endpoints for control of remote sink or source devices. The "Over TP" ports are simply pass-through connections to DTP endpoints. There is no RS-232 or IR insertion from any DTP T DWP 4K control port to the "Over TP" ports.
Serial control pass-through port	Bidirectional RS-232
Connector	(1) 3.5 mm captive screw connector, 5-pole (shared with IR port)
Baud rate and protocol	300 to 115200 baud, 8 or 7 data bits, 1 or 2 stop bits, non-parity (default), even or odd parity
Serial control pin configuration	1 = Tx, 2 = Rx, 3 = Gnd
IR pass-through control port	1 bidirectional TTL level (0 to 5V) modulated infrared control from 30 kHz up to 60 kHz (shared with RS-232 port)
IR control pin configuration	3 = Gnd, 4 = IR Tx, 5 = IR Rx
General
Power supply	External Input: 100-240 VAC, 50-60 Hz Output: 12 VDC, 1.5 A, 18 watts
Power consumption
Device	5.6 watts
Device and power supply	7.8 watts
NOTE     Each transmitter or receiver can be powered either locally by an external power supply or remotely by receiver or transmitter on the other end of the twisted pair cable.
Temperature/humidity	Storage: -40 to +158 °F (-40 to +70 °C) / 10% to 90%, noncondensing Operating: +32 to +122 °F (0 to +50 °C) / 10% to 90%, noncondensing
Cooling	Convection, no vents
Thermal dissipation
Device	19.0 BTU/hr
Device and power supply	26.6 BTU/hr
Enclosure type	Metal
Enclosure dimensions
Faceplate	Two 2.6" H* x 1.3" W x 0.2" D (6.6 cm H x 3.3 cm W x 0.6 cm D) Fits the opening in a 2 gang decorator wallplate.
Device	Two 2.7" H x 3.5" W x 1.9" D (6.9 cm H x 8.9 cm W x 4.8 cm D)
Product weight	0.4 lbs (0.2 kg)
Regulatory compliance	CE, c-UL UL, CE**, C-tick, FCC Class A**, ICES, VCCI, Complies with the appropriate requirements of RoHS, WEEE
NOTE     **CE and FCC testing is conducted with STP cable.
Product warranty	3 years parts and labor
Everlast power supply warranty	7 years parts and labor
NOTE     All nominal levels are at ±10%.
NOTE     Specifications are subject to change without notice.
NOTE     Shipping dimensions and weights are available at www.extron.com.
(4372-090518-D6)

Versand-Abmessung und -Gewicht
Teilenummer	Höhe	Breite	Tiefe	Gewicht
60-1498-12	7,6 cm	26,7 cm	19,1 cm	0,79 kg
60-1498-13	7,6 cm	26,7 cm	19,1 cm	0,79 kg