DTP T FB 332

Technische Daten

DTP T FB 332
Video
VGA
Gain	Unity
Bandwidth	170 MHz (-3 dB)
Crosstalk	-50 dB @ 10 MHz, -30 dB @ 100 MHz
Switching speed	<5 ms. (max)
HDMI
Maximum data rate	6.75 Gbps (2.25 Gbps per color)
Maximum pixel clock	165 MHz
Resolution range	Up to 1920x1200 or 1080p @ 60 Hz; 2k
Formats	RGB and YCbCr digital video
Standards	DVI 1.0, HDMI, HDCP 1.1, CEA-861E
Video input — HDMI
Number/signal type	1 HDMI input (or single-link DVI-D with the appropriate DVI-HDMI adapters)
Connectors	1 female HDMI type A
Video input — VGA
Number/signal type	1 VGA-QXGA
Connectors	1 female 15-pin HD
Nominal level	0.7 Vp-p for RGB
Min./max. level	Analog, 0.3 V to 1.5 Vp-p with no offset
Impedance	75 ohms
Horizontal frequency	15 kHz to 145 kHz
Vertical frequency	30 Hz to 170 Hz
Return loss	<-40 dB @ 5 MHz
NOTE     The VGA input is digitized and output as DTP. The VGA signal is not scaled.
Sync — VGA
Input type	RGBHV
Input level	1.9 V to 5.0 Vp-p
S/N	>90 dB at maximum input (unweighted)
Max. input voltage	5.0 Vp-p
Interconnection between transmitter and receiver
Number/signal type	1 DTP 330 output
Connector	1 female RJ-45
Termination standard	TIA/EIA T568B
Transmission distance	Up to 330' (100 m) using shielded twisted pair cable or XTP DTP 24 STP cable
Cable requirements	Solid conductor, 24 AWG or better
Cable recommendations	400 MHz bandwidth, STP (shielded twisted pair)
NOTE     Extron XTP DTP 24 shielded twisted pair cable is strongly recommended for optimal performance.
NOTE     Input and output mode signaling: DTP:             HDMI with embedded audio, analog audio, RS-232 and IR, and remote power HDBaseT:   HDMI with embedded audio plus RS-232 and IR
Audio
Gain	Unbalanced output: 0 dB; balanced output +6 dB
Frequency response	20 Hz to 20 kHz, ±0.5 dB
THD + Noise	0.01% @ 1 kHz at nominal level
S/N	>90 dB, at maximum input (unweighted)
Crosstalk	<-45 dB @ 20 kHz, or -72 dB @ 1 kHz or below
Stereo channel separation	>80 dB @ 1 kHz to 20 kHz
Audio input
Number/signal type	1 analog stereo, unbalanced or 1 digital audio, embedded in the HDMI
Connectors	1 female 3.5 mm mini stereo jack 1 female HDMI Type A (shared with video input)
Source formats
HDMI	LPCM up to 7.1/24-bit/192 kHz, Dolby TrueHD, Dolby Digital Plus, Dolby Digital EX, Dolby Digital 5.1, Dolby Digital 2/0 Surround, Dolby Digital 2/0, DTS-HD Master Audio, DTS-HD, DTS-ES Discrete 6.1, DTS-ES Matrix 6.1, DTS Digital Surround 5.1, DTS 2 Channel
Analog	Analog stereo audio
Impedance	10k ohms, DC coupled
Nominal level	-10 dBV
Maximum level	+6dBV, unbalanced
CMRR	>60 dB typ @ 1 kHz
Input gain adjustment	-18 dB to +24 dB, 1 dB steps, adjustable per input
NOTE     0 dBu = 0.775 Vrms, 0 dBV = 1 Vrms, 0 dBV ? 2 dBu
Audio output
Number/signal type	1 analog audio over DTP signal, or 1 embedded digital audio over DTP signal
Connectors	1 RJ-45 jack
Communications — switcher
Serial control port	RS-232 via (1) 3.5 mm, 3 pole captive screw connector
Serial control pin configuration	Pin 1 = Tx, pin 2 = Rx, pin 3 = Gnd
Baud rate and protocol (RS-232)	9600 baud, 8 data bits, 1 stop bit, no parity
USB control port	1 front panel female mini USB, type B
USB standards	USB 2.0, high speed
Program control	Extron Simple Instruction Set (SISTM)
Communications — RS-232/IR over TP
NOTE     Protocol is mirrored between the connected DTP 330 Rx and the OverDTP output port. Signals from a control device pass into the Over TP port, are embedded with the DTP signal, and sent to the DTP 330 Rx endpoint for control of remote sink and source devices. The Over TP port is a pass-through connection to the DTP endpoint. There is no RS-232 or IR insertion from the DTP T FB 332 control port to the Over TP port.
Serial control pass-through port	1 RS-232 and IR via (1) 3.5 mm, 5-pole captive screw connector
Serial control pin configuration	Pin 1 = Tx, pin 2 = Rx, pin 3 = Gnd
Baud rates	300 to 115200 baud
Protocol	8 or 7 data bits 1 or 2 stop bits no parity (default) even or odd parity
IR pass-through control port	TTL level (0 to 5 V) modulated infrared control from 30 kHz up to 60 kHz
IR control pin configuration	3 = GND, 4 = IR Tx, 5 = IR Rx
General
Power supply	External Input: 100 to 240 VAC, 50-60 Hz Output: 12 VDC, 1.5 A, 18 watts
Power consumption
Device	4.7 watts, 12 VDC
Device and power supply	6.2 watts, 100-240 VAC, 50-60 Hz
Temperature/humidity	Storage: -40 to +158 °F (-40 to +70 °C) / 10% to 90%, noncondensing Operating: +32 to +104 °F (0 to +40 °C) / 10% to 90%, noncondensing
Cooling	Convection, no vents
Thermal dissipation
Device	15.9 BTU/hr
Device and power supply	21.1 BTU/hr
Mounting
Floor box mount	Ackermann GB3/OBO Betterman floor box, MK Electric CableLink Plus Single Pan floor box, MK Electric CableLink Plus Modular floor box, ElectraPlan floor box, and PUK floor box mountable
NOTE     See the DTP T FB 332 User Guide for mounting considerations.
Enclosure type	Metal
Enclosure dimensions	2.3" H x 2.8" W x 5.2" D* (5.9 cm H x 7.2 cm W x 13.2 cm D) (Dimensions exclude connectors) * Depth is 6.1" (15.5 cm) including mounting tabs
Product weight	1.1 lbs (0.5 kg)
Regulatory compliance	CE, c-UL UL, CE**, C-tick, FCC Class A**, ICES, VCCI, Complies with the appropriate requirements of RoHS, WEEE
NOTE     **CE and FCC testing is conducted with STP (shielded twisted pair) cable.
Product warranty	3 years parts and labor
Everlast power supply warranty	7 years parts and labor
NOTE     All nominal levels are at ±10%.
NOTE     Specifications are subject to change without notice.
(4342-083118-D11)

Versand-Abmessung und -Gewicht
Teilenummer	Höhe	Breite	Tiefe	Gewicht
60-1568-52	7,5 cm	26,7 cm	19,1 cm	1,34 kg