DTP T MK 332

Technische Daten

DTP T MK 332
NOTE     *Appropriate HDMI to DVI-D cables or adapters are required for DVI signal input/output.
Video
Maximum data rate	6.75 Gbps (2.25 Gbps per color)
Maximum pixel clock	165 MHz
Resolution range	Up to 1920x1200 or 1080p @ 60 Hz; 8 bit color depth 2048x1080p @ 60 Hz (2K)
Formats	RGB and YCbCr digital video
Standards	DVI 1.0, HDMI, HDCP 1.2, EDID 1.3, CEA-861E
Video input — HDMI
Number/signal type	1 single link HDMI (or DVI-D*) input
Connectors	1 female HDMI type A
Video input — VGA
Number/signal type	1 analog RGBHV
Connectors	1 female 15-pin HD (RGB)
Nominal level	0.7 Vp-p for RGB
Minimum/maximum levels	0.3 V to 1.45 Vp-p
Impedance	75 ohms
Horizontal frequency	15 kHz to 130 kHz
Vertical frequency	30 Hz to 150 Hz
Return loss	<-30 dB @ 5 MHz
DC offset (max. allowable)	250 mV
Interconnection between transmitter and receiver
Signal type	1 DTP 330 output
Connectors	1 female RJ-45
Termination standards	TIA/EIA T568B
DTP signal
Signal transmission distance	Up to 330' (100 m) using shielded twisted pair (STP) cable or XTP DTP 24 cable
Cable requirements	Solid conductor, 24 AWG or better
Cable recommendations	400 MHz bandwidth STP cable
NOTE     Extron XTP DTP 24 shielded twisted pair cable is strongly recommended for optimal performance.
NOTE     Input and output mode signaling: DTP:             HDMI with embedded audio, analog audio, RS-232 and IR, and remote power HDBaseT:   HDMI with embedded audio plus RS-232 and IR
Audio
Gain	Unbalanced output: 0 dB; balanced output +6 dB
Frequency response	20 Hz to 20 kHz, ±0.5 dB
THD + Noise	0.03% @ 20 Hz to 20 kHz at maximum output
S/N	>90 dB, at maximum output (15 dBu), balanced (unweighted)
Stereo channel separation	>80 dB @ 1 kHz to 20 kHz
Audio input
Number/signal type
Analog audio (over DTP)	2 stereo, unbalanced
NOTE     Analog audio is not embedded onto the digital video signal.
Digital audio	1 embedded digital audio on DTP
Embedded digital audio source formats	2-ch PCM, PCM, Dolby Digital 2/0, Dolby Digital 2/0 Surround, Dolby Digital 5.1, Dolby Digital EX, DTS Digital Surround 5.1, DTS-ES Matrix 6.1, DTS-ES Discrete 6.1
Connectors	(2) 3.5 mm stereo jack, 2 channel; tip (L); ring (R); sleeve (ground)
Impedance	>10k ohms, DC coupled
Nominal level	-10 dBV (316 mVrms)
Maximum level	+7 dBu, unbalanced
NOTE     0 dBu = 0.775 Vrms, 0 dBV = 1 Vrms, 0 dBV ? 2 dBu
Audio output
Number/signal type
Analog audio (over DTP)	1 stereo, unbalanced
Digital audio	1 embedded digital audio on DTP
Embedded digital audio source formats	2-ch PCM, PCM, Dolby Digital 2/0, Dolby Digital 2/0 Surround, Dolby Digital 5.1, Dolby Digital EX, DTS Digital Surround 5.1, DTS-ES Matrix 6.1, DTS-ES Discrete 6.1
Connectors	1 female RJ-45 jack
Communications — transmitter
Serial control port	RS-232 via (1) 3.5 mm, 3-pole captive screw connector for RS-232 control (±5 V)
Baud rate and protocol	9600 baud rate, 8 data bits, 1 stop bit, no parity
USB control port	1 side panel female mini USB type B
USB standards	USB 2.0, high speed
Program control	Extron Simple Instruction Set (SIS™)
Communications — external device (pass-through)
Serial control pass-through port	Bidirectional RS-232
Connector
DTP output	(1) 3.5 mm captive screw connector, 5-pole (shared with IR pass-through port)
Baud rates	300 to 115200 baud
Protocol	Data bits = 5 - 8 Stop bits = 1 or 2 Parity = odd, even, none Flow control = XON, XOFF, none
IR pass-through control port	TTL level (0 to 5 V) modulated infrared control from 30 kHz up to 60 kHz
DTP output	(1) 3.5 mm captive screw connector, 5-pole (shared with IR pass-through port)
NOTE     Protocol is mirrored between the connected DTP 330 endpoints and the "Over TP" ports on the DTP T 332 MK. Signals from a control device pass into each "Over TP" port, are embedded with the TP signal and sent to the individual DTP 330 endpoints for control of remote sink or source devices.
General
Power supply	External Input: 100 to 240 VAC, 50-60 Hz Output: 12 VDC, 1.5 A, 18 watts
Power consumption
Device	4.4 watts, 12 VDC
Device and power supply	5.7 watts, 100-240 VAC, 50-60 Hz
NOTE     Each transmitter or receiver can be powered either locally by an external power supply or remotely by an receiver or transmitter on the other end of the twisted pair cable.
Temperature/humidity	Storage: -40 to +158 °F (-40 to +70 °C) / 10% to 90%, noncondensing Operating: +32 to +104 °F (0 to +40 °C) / 10% to 90%, noncondensing
Cooling	Convection, no vents
Thermal dissipation
Device	14.9 BTU/hr
Device and power supply	19.4 BTU/hr
Mounting
Furniture or wall mount	Yes, with an MK 2-gang electrical junction box
Enclosure type	Metal
Enclosure dimensions
Faceplate	3.4" H x 5.8" W x 0.5" D (2-gang) (8.6 cm H x 14.7 cm W x 1.4 cm D)
Device	1.9" H x 4.3" W x 1.4" D (4.9 cm H x 10.9 cm W x 3.5 cm D) (Depth excludes connectors. Fits some MK 2-gang boxes.)
Product weight	0.7 lbs (0.3 kg)
Shipping weight	3 lbs (2 kg)
Regulatory compliance	CE, c-UL UL, CE**, C-tick, FCC Class A**, ICES, VCCI, Complies with the appropriate requirements of RoHS, WEEE
NOTE     **CE and FCC testing is conducted with STP (shielded twisted pair) cable.
Product warranty	3 years parts and labor
Everlast power supply warranty	7 years parts and labor
NOTE     All nominal levels are at ±10%.
NOTE     Specifications are subject to change without notice.
(4335-083118-D5)

Versand-Abmessung und -Gewicht
Teilenummer	Höhe	Breite	Tiefe	Gewicht
60-1467-52	26,7 cm	19,1 cm	7,5 cm	0,89 kg
60-1567-52	7,5 cm	26,7 cm	19,1 cm	0,89 kg