DTP2 R 211

Technische Daten

DTP2 211 Series Tx/Rx
Specification
Frame rate 1	24, 25, 30, 50, or 60 fps
Chroma sampling 1	4:4:4, 4:2:2, or 4:2:0
Color bit depth 1	8, 10, or 12 bits per color
Signal type	HDMI 1.4, 2.0b; HDCP 2.2, 1.4
Max. video data rate	18 Gbps (6 Gbps per color)
NOTE     This product consists of a transmitter (DTP2 T 211) and a receiver (DTP2 R 211), sold separately, with twisted pair cables linking the transmitter and receiver.
NOTE     1Subject to the maximum data rate limit. Use our calculator at www.extron.com/4Kdatarate to determine video parameters supported by this data rate.
Video
Maximum data rate	18 Gbps (6 Gbps per color)
Maximum pixel clock	600 MHz
Resolution range	2560x1600 @ 60 Hz or 1080p @ 60 Hz, 12-bit color, 4K (4096x2160) @ 30 Hz, UHD (3840x2160) @ 30 Hz, 4K (4096x2160) @ 60 Hz*, UHD (3840x2160) @ 60 Hz, (*4:2:0 color space)
Color bit depth	8, 10, or 12 bits — subject to the maximum data rate limit
Formats	RGB and YCbCr digital video
Standards	DVI 1.0; HDMI 1.4, 2.0b; HDCP 1.4, 2.2, CEA-861E
Video input — transmitter
Number/signal type	1 single link HDMI (or DVI-D*)
Connectors	1 female HDMI type A
NOTE     *Appropriate HDMI to DVI-D cables or adapters are required for DVI signal input/output.
Interconnection between transmitter and receiver
Connectors	1 female RJ-45 per unit
Termination standard	TIA/EIA T568B
Signal transmission distance	Up to 330' (100 m) using shielded twisted pair (STP) cable or XTP DTP 24 STP cable
Cable requirements	Solid conductor, 24 AWG or better
Cable recommendations	400 MHz bandwidth, STP (shielded twisted pair)
NOTE     Extron XTP DTP 24 shielded twisted pair cable is strongly recommended for optimal performance.
Video output — receiver
Number/signal type	1 single link HDMI (or DVI-D*)
Connectors	1 female HDMI type A
Audio
Gain	Unbalanced output: 0 dB; balanced output +6 dB
Frequency response	20 Hz to 20 kHz, ±0.5 dB
THD + Noise	0.03% @ 20 Hz to 20 kHz at maximum output
S/N	>90 dB, at maximum output (15 dBu), balanced (unweighted)
Stereo channel separation	>80 dB @ 1 kHz to 20 kHz
Audio input
Number/signal type	1 PC level stereo, unbalanced 1 Digital Embedded Audio on HDMI
NOTE     Analog audio can be configured for embedding onto the digital video signal at the Transmitter. Embedded digital audio can be (configured) de-embedded from the digital video signal at the Receiver end.
Connectors	(1) 3.5 mm stereo jack, 2 channel; tip (L), ring (R), sleeve (ground) (1) Female HDMI
Impedance	>10k ohms, DC coupled
Nominal level	-10 dBV (316 mVrms)
Maximum level	+7 dBV (unbalanced)
NOTE     0 dBu = 0.775 Vrms, 0 dBV = 1 Vrms, 0 dBV ? 2 dBu
Audio output
Number/signal type	1 stereo (2 channel), balanced/unbalanced
Connectors	(1) 3.5 mm captive screw connector, 5 pole
Impedance	50 ohms unbalanced, 100 ohms balanced
Gain error	±0.1 dB channel to channel
Maximum level (600 ohm)	>+11 dBu, balanced
Communication — external device (pass-through, unidirectional or bidirectional)
Serial control port input/output
Transmitter	RS-232 via (1) 3.5 mm, 5 pole captive screw connector for RS-232 control (±5 V) (connector is shared with IR control port)
Receiver	1 set of proprietary signals on a female RJ-45 jack
Serial control port output/input
Transmitter	1 set of proprietary signals on a female RJ-45 jack
Receiver	RS-232 via a 3.5 mm, 3 pole captive screw connector
Baud rate and protocol	300 to 115200 baud, 8 or 7 data bits, 1 or 2 stop bits, non-parity (default), even or odd parity
Serial control pin configuration	1 = Tx, 2 = Rx, 3 = Gnd
IR control port	(1) 3.5 mm, captive screw connector, 5 pole (connector is shared with RS-232 control port) TTL level (0 to 5 V) modulated infrared control from 30 kHz up to 60 kHz
IR control pin configuration	3 = Gnd, 4 = IR Tx, 5 = IR Rx
General
Power supply	External Input: 100-240 VAC, 50-60 Hz Output: 12 VDC, 1.5 A, 18 Watts
Power consumption
Transmitter
Device	TBD watts, 12 VDC
Device and power supply	TBD watts, 100-240 VAC, 50-60 Hz
Receiver
Device	TBD watts, 12 VDC
Device and power supply	TBD watts, 100-240 VAC, 50-60 Hz
NOTE     Each transmitter or receiver can be powered either locally by an external power supply or remotely by receiver or transmitter on the other end of the twisted pair cable.
Remote power capability	Supports one endpoint (DTP2)
NOTE     DTP2 devices can only send power to other DTP2 devices. DO NOT send power to DTP devices or they will be damaged.
Temperature/humidity	Storage: -40 to +158 °F (-40 to +70 °C) / 10% to 90%, noncondensing Operating: +32 to +122 °F (0 to +50 °C) / 10% to 90%, noncondensing
Cooling	Convection, no vents
Thermal dissipation
Transmitter
Device	TBD BTU/hr
Device and power supply	TBD BTU/hr
Receiver
Device	TBD BTU/hr
Device and power supply	TBD BTU/hr
Mounting
Rack mount	Yes, with optional 1U high rack shelf
Furniture mount	Yes, with optional under-desk mounting kit
Enclosure type	Metal
Enclosure dimensions
Transmitter	1.0" H x 4.3" W x 6.0" D (quarter rack wide) (2.5 cm H x 10.9 cm W x 15.2 cm D) (Depth excludes connectors.)
Receiver	1.0" H x 4.3" W x 6.0" D (quarter rack wide) (2.5 cm H x 10.9 cm W x 15.2 cm D) (Depth excludes connectors.)
Product weight
Transmitter	TBD lbs (TBD kg)
Receiver	TBD lb (TBD kg)
Regulatory compliance	CE, C-Tick, FCC Class A, ICES, VCCI, KCC, c-UL, UL UL rated for use in plenum airspaces: meets UL for heat and smoke release, excluding the power supply.
Product warranty	3 years parts and labor
Everlast power supply warranty	7 years parts and labor
NOTE     All nominal levels are at ±10%.
NOTE     Specifications are subject to change without notice.
(4339-D3)