DTP2 R 212
EUR
1848.00
€ 1848.00
Hersteller
Extron
Art.Nr.
60-1588-52
EAN
60-1588-52
Produktbeschreibung
Hauptmerkmale
- Empfängt HDMI-, Steuerungs- und analoge Audiosignale bis zu 100 m über ein geschirmtes CATx-Kabel
- Der HDMI-Eingang eignet sich ideal für die Verbindung mit einer lokalen Quelle, wie z. B. ein Laptop oder ein ShareLink-Funkgateway für Präsentationen in Arbeitsgruppen
- Unterstützt Computer- und Videoauflösungen bis zu 4K/60 mit 4:4:4
- Automatische Umschaltung zwischen den Eingängen
- Unterstützt HDMI 2.0b-Spezifikationen, einschließlich Datenraten bis zu 18 Gbps, HDR, Deep Color bis zu 12 Bit, 3D, verlustfreier HD-Audioformate und CEC
- Unterstützung von High Dynamic Range Video (HDR)
Modell | Beschreibung der Version | Teilenummer | |
---|---|---|---|
DTP2 R 212 | 4K/60 HDMI-Empfänger und Umschalter - 100 m | 60-1588-52 | |
DTP2 R 212 SA | 4K/60 HDMI-Empfänger und -Umschalter mit Verstärker - 100 m | 60-1588-53 |
Technische Daten
Technische Daten
-
DTP2 R 212 and DTP2 R 212 SA Switching Receivers specification Frame rate 1 24, 25, 30, 50, or 60 fps Chroma sampling 1 4:4:4, 4:2:2, or 4:2:0 Color bit depth 1 8, 10, 12 bits per color Signal type HDMI 2.0b, HDCP 2.2 Max. video data rate 18 Gbps (6 Gbps per color) NOTE 1Subject to the maximum data rate limit. Use our calculator at www.extron.com/4Kdatarate to determine video parameters supported by this data rate. Video Maximum data rate 18 Gbps (6 Gbps per color) Maximum pixel clock 600 MHz Resolution range 2560x1600 @ 60 Hz or 1080p @ 60 Hz, 12-bit color
4K (4096x2160) @ 30 Hz, UHD (3840x2160) @ 30 Hz
4K (4096x2160) @ 60 Hz*, UHD (3840x2160) @ 60 Hz
*4:2:0 color spaceFormats RGB and YCbCr digital video Standards DVI 1.0, HDMI 2.0b, HDMI 1.4a, CEA-861F, HDCP 2.2, HDCP 1.4 Video input Number/signal type 1 DTP2
1 HDMI (or single link DVI-D, with appropriate DVI-HDMI adapters)Connectors 1 female RJ-45
1 female HDMI, type AInterconnection between transmitter and receiver Connectors 1 female RJ-45 per unit Termination standard TIA/EIA T568B Signal transmission distance Up to 330' (100m) using shielded twisted pair (STP) cable or XTP DTP 24 STP cable Cable requirements Solid conductor, 24 AWG or better Cable recommendations 400 MHz bandwidth, STP (shielded twisted pair) NOTE Extron XTP DTP 24 shielded twisted pair cable is strongly recommended for optimal performance. Video output Number/signal type 1 HDMI output Connectors 1 female HDMI, type A Audio Gain Unbalanced output: 0 dB; balanced output: +6 dB Frequency response 20 Hz to 20 kHz, ±0.5 dB THD + Noise 0.03% @ 20 Hz to 20 kHz at maximum output S/N >90 dB, at maximum output (15 dBu), balanced (unweighted) Stereo channel separation >80 dB @ 1 kHz to 20 kHz Bass +12 dB to -24 dB @ 100 Hz Treble +12 dB to -24 dB @ 8 Hz Audio input Number/signal type HDMI input 1 embedded digital audio from HDMI DTP/DTP2 input 1 stereo, unbalanced analog
1 embedded digital audio from DTPEmbedded digital audio source formats 2-ch PCM Connectors 1 female HDMI type A
1 female RJ-45 connector for audio over DTPImpedance >10k ohms unbalanced, >20k ohms balanced Nominal level Over DTP input: +4 dBu, -10 dBu, adjustable Maximum level +15 dBu at rated THD+N when input gain is set to 0dB CMRR >80 dB @ 1 KHz NOTE 0 dBu = 0.775 Vrms, 0 dBV = 1 Vrms, 0 dBV?2 dBu Audio output — Analog Number/signal type DTP2 R 212 1 stereo, balanced/unbalanced analog audio output (fixed and variable) DTP2 R 212 SA 1 stereo, balanced/unbalanced analog audio output (fixed and variable)
1 amplifier output (1 stereo [default] or 2 mono, 2 channels total)Connectors (1) 3.5 mm captive screw connector, 5-pole
1 female HDMI type AImpedance 50 ohms unbalanced, 100 ohms balanced Gain error ±0.5 dB channel to channel Maximum level (Hi-Z) >+21 dBu, balanced; >+15 dBu, unbalanced Output volume range 0 to -100 dB in 1 dB steps Nominal level when the main volume is set to default -2 dBu (632 mVrms) balanced output NOTE 0 dBU = 0.775 Vrms, 0 dBV = 1 Vrms, 0 dBV ? 2 dBu Audio output — power amplifier (DTP2 R 212 SA) Number/signal type 1 stereo or 2 mono (2 channels total) Connector (1) 5 mm captive screw connector, 4-pole Load impedance 4 ohms, minimum Amplifier type Class D Output power 8 watts rms per channel, 8 ohms, 1 kHz, 1% THD
15 watts rms per channel, 4 ohms, 1 kHz, 1% THDFrequency response 20 Hz to 20 kHz, +1/-3 dB @ 8 ohms THD + Noise <0.1% -3 dB below clipping @ 1 kHz, 8 ohm load S/N 90 dB, 20 Hz to 20 kHz, unweighted Damping factor >100 @ 8 ohms Communications — switcher Serial control port 1 RS-232, 3.5 mm captive screw connector, 3-pole, rear panel Pin configuration Pin 1 = Tx, pin 2 = Rx, pin 3 = Gnd Baud rate and protocol 9600 baud, 8 data bits, 1 stop bit, no parity USB control port 1 female mini-USB, type B, front panel USB standards USB 2.0, high speed Ethernet data rate 10/100Base-T, half/full duplex, with autodetect Ethernet protocol ARP, ICMP (ping), IP, TCP, DHCP, HTTP, Telnet, SMTP Program control Extron PCS®
Extron Simple Instruction Set (SIS™)
Microsoft® Internet Explorer®, TelnetCommunication – RS-232/IR over DTP2 and RS-232/IR Display Control — external device (IR/RS-232 over DTP2 and sink displays) Serial control pass-through port 1 -232 via 3.5 mm, 5-pole captive screw connector (shared with IR port) Baud rates 300 to 115200 baud Protocol 8 or 7 data bits
1 or 2 stop bits
No parity (default), even or odd paritySerial control pin configuration 1 = Tx, 2 = Rx, 3 = Gnd IR control pass-through ports 1 directional TTL level (0 to 5 V) modulated infrared control from 30 kHz up to 60 kHz Output/DTP Rx 3.5 mm captive screw connector, 5-pole (shared with RS-232 port) IR control pin configuration 3 = Gnd, 4 = IR Tx, 5 = IR Rx General Power supply External
Input: 100-240 VAC, 50-60 Hz
Output: 12 VDC, 4A, 48 wattsPower input requirements 12 VDC Power consumption Device TBD watts, 12 VDC Device and power supply TBD watts, 12 VDC Remote power capability DTP2 R 212 Can transmit or receive power via DTP2 Temperature/humidity Storage: -40 to +158 °F (-40 to +70 °C) / 10% to 90%, noncondensing
Operating: +32 to +122 °F (0 to +50 °C) / 10% to 90%, noncondensingCooling Convection, vents on top and sides Thermal dissipation Device TBD BTU/hr Device and power supply TBD BTU/hr Mounting Rack mount Yes, with optional rack shelf kit Furniture mount Yes, with optional under-desk mounting kit Enclosure type Metal Enclosure dimensions 1.00" H x 13.1" W x 6.0" D (1" high, 3/4 rack wide)
(2.54 cm H x 33.3 cm W x 15.2 cm D)
(Depth excludes connectors)Product weight TBD lb (TBD kg) Vibration ISTA 1A in carton (International Safe Transit Association) Regulatory compliance Safety CE, c-UL, UL EMI/EMC CE, C-Tick, FCC Class A, ICES, VCCI Product warranty 3 years parts and labor Everlast power supply warranty 7 years parts and labor NOTE All nominal levels are at ±10%. NOTE Specifications are subject to change without notice. ( CMS-082217-D2)