DTP2 T 211
EUR
780.00
€ 780.00
Hersteller
Extron
Art.Nr.
60-1631-52
EAN
60-1631-52
Produktbeschreibung
Hauptmerkmale
- Überträgt HDMI-, Steuerungs- und analoge Audiosignale bis zu 100 m über ein geschirmtes CATx-Kabel
- Unterstützt Computer- und Videoauflösungen bis zu 4K/60 mit 4:4:4
- Embedding von analogem Stereo-Audio
- Unterstützt HDMI 2.0b-Spezifikationen, einschließlich Datenraten bis zu 18 Gbps, HDR, Deep Color bis zu 12 Bit, 3D, verlustfreier HD-Audioformate und CEC-Durchleitung
- Unterstützung von HDR - High Dynamic Range Video
- HDCP 2.2-konform
Modell | Beschreibung der Version | Teilenummer | |
---|---|---|---|
DTP2 T 211 | 4K/60 HDMI -Sender - 100 m | 60-1631-52 |
Technische Daten
Technische Daten
-
DTP2 211 Series Tx/Rx Specification Frame rate 1 24, 25, 30, 50, or 60 fps Chroma sampling 1 4:4:4, 4:2:2, or 4:2:0 Color bit depth 1 8, 10, or 12 bits per color Signal type HDMI 1.4, 2.0b; HDCP 2.2, 1.4 Max. video data rate 18 Gbps (6 Gbps per color) NOTE This product consists of a transmitter (DTP2 T 211) and a receiver (DTP2 R 211), sold separately, with twisted pair cables linking the transmitter and receiver. NOTE 1Subject to the maximum data rate limit. Use our calculator at www.extron.com/4Kdatarate to determine video parameters supported by this data rate. Video Maximum data rate 18 Gbps (6 Gbps per color) Maximum pixel clock 600 MHz Resolution range 2560x1600 @ 60 Hz or 1080p @ 60 Hz, 12-bit color,
4K (4096x2160) @ 30 Hz, UHD (3840x2160) @ 30 Hz,
4K (4096x2160) @ 60 Hz*, UHD (3840x2160) @ 60 Hz,
(*4:2:0 color space)Color bit depth 8, 10, or 12 bits — subject to the maximum data rate limit Formats RGB and YCbCr digital video Standards DVI 1.0; HDMI 1.4, 2.0b; HDCP 1.4, 2.2, CEA-861E Video input — transmitter Number/signal type 1 single link HDMI (or DVI-D*) Connectors 1 female HDMI type A NOTE *Appropriate HDMI to DVI-D cables or adapters are required for DVI signal input/output. Interconnection between transmitter and receiver Connectors 1 female RJ-45 per unit Termination standard TIA/EIA T568B Signal transmission distance Up to 330' (100 m) using shielded twisted pair (STP) cable or XTP DTP 24 STP cable Cable requirements Solid conductor, 24 AWG or better Cable recommendations 400 MHz bandwidth, STP (shielded twisted pair) NOTE Extron XTP DTP 24 shielded twisted pair cable is strongly recommended for optimal performance. Video output — receiver Number/signal type 1 single link HDMI (or DVI-D*) Connectors 1 female HDMI type A Audio Gain Unbalanced output: 0 dB; balanced output +6 dB Frequency response 20 Hz to 20 kHz, ±0.5 dB THD + Noise 0.03% @ 20 Hz to 20 kHz at maximum output S/N >90 dB, at maximum output (15 dBu), balanced (unweighted) Stereo channel separation >80 dB @ 1 kHz to 20 kHz Audio input Number/signal type 1 PC level stereo, unbalanced
1 Digital Embedded Audio on HDMINOTE Analog audio can be configured for embedding onto the digital video signal at the Transmitter. Embedded digital audio can be (configured) de-embedded from the digital video signal at the Receiver end. Connectors (1) 3.5 mm stereo jack, 2 channel; tip (L), ring (R), sleeve (ground)
(1) Female HDMIImpedance >10k ohms, DC coupled Nominal level -10 dBV (316 mVrms) Maximum level +7 dBV (unbalanced) NOTE 0 dBu = 0.775 Vrms, 0 dBV = 1 Vrms, 0 dBV ? 2 dBu Audio output Number/signal type 1 stereo (2 channel), balanced/unbalanced Connectors (1) 3.5 mm captive screw connector, 5 pole Impedance 50 ohms unbalanced, 100 ohms balanced Gain error ±0.1 dB channel to channel Maximum level (600 ohm) >+11 dBu, balanced Communication — external device (pass-through, unidirectional or bidirectional) Serial control port input/output Transmitter RS-232 via (1) 3.5 mm, 5 pole captive screw connector for RS-232 control (±5 V) (connector is shared with IR control port) Receiver 1 set of proprietary signals on a female RJ-45 jack Serial control port output/input Transmitter 1 set of proprietary signals on a female RJ-45 jack Receiver RS-232 via a 3.5 mm, 3 pole captive screw connector Baud rate and protocol 300 to 115200 baud, 8 or 7 data bits, 1 or 2 stop bits, non-parity (default), even or odd parity Serial control pin configuration 1 = Tx, 2 = Rx, 3 = Gnd IR control port (1) 3.5 mm, captive screw connector, 5 pole (connector is shared with RS-232 control port)
TTL level (0 to 5 V) modulated infrared control from 30 kHz up to 60 kHzIR control pin configuration 3 = Gnd, 4 = IR Tx, 5 = IR Rx General Power supply External
Input: 100-240 VAC, 50-60 Hz
Output: 12 VDC, 1.5 A, 18 WattsPower consumption Transmitter Device TBD watts, 12 VDC Device and power supply TBD watts, 100-240 VAC, 50-60 Hz Receiver Device TBD watts, 12 VDC Device and power supply TBD watts, 100-240 VAC, 50-60 Hz NOTE Each transmitter or receiver can be powered either locally by an external power supply or remotely by receiver or transmitter on the other end of the twisted pair cable. Remote power capability Supports one endpoint (DTP2) NOTE DTP2 devices can only send power to other DTP2 devices. DO NOT send power to DTP devices or they will be damaged. Temperature/humidity Storage: -40 to +158 °F (-40 to +70 °C) / 10% to 90%, noncondensing
Operating: +32 to +122 °F (0 to +50 °C) / 10% to 90%, noncondensingCooling Convection, no vents Thermal dissipation Transmitter Device TBD BTU/hr Device and power supply TBD BTU/hr Receiver Device TBD BTU/hr Device and power supply TBD BTU/hr Mounting Rack mount Yes, with optional 1U high rack shelf Furniture mount Yes, with optional under-desk mounting kit Enclosure type Metal Enclosure dimensions Transmitter 1.0" H x 4.3" W x 6.0" D (quarter rack wide)
(2.5 cm H x 10.9 cm W x 15.2 cm D)
(Depth excludes connectors.)Receiver 1.0" H x 4.3" W x 6.0" D (quarter rack wide)
(2.5 cm H x 10.9 cm W x 15.2 cm D)
(Depth excludes connectors.)Product weight Transmitter TBD lbs (TBD kg) Receiver TBD lb (TBD kg) Regulatory compliance CE, C-Tick, FCC Class A, ICES, VCCI, KCC, c-UL, UL
UL rated for use in plenum airspaces: meets UL for heat and smoke release, excluding the power supply.Product warranty 3 years parts and labor Everlast power supply warranty 7 years parts and labor NOTE All nominal levels are at ±10%. NOTE Specifications are subject to change without notice. (4339-D3)