DTP2 T 212

Technische Daten

DTP2 T 212
specification
Frame rate 1	24, 25, 30, 50, or 60 fps
Chroma sampling 1	4:4:4, 4:2:2, or 4:2:0
Color bit depth 1	8, 10, or 12 bits per color
Signal type	HDMI 2.0b; HDCP 2.2/1.x
Max. video data rate	18 Gbps (6 Gbps per color)
NOTE     1Subject to the maximum data rate limit. Use our calculator at www.extron.com/4Kdatarate to determine video parameters supported by this data rate.
Video
Maximum data rate	18 Gbps (6 Gbps per color)
Maximum pixel clock	600 MHz
Resolution range	Up to 2560x1600* @ 60 Hz or UHD (3840x2160) @ 60 Hz, (* 4:4:4 chroma subsampling)
HDMI cable input Max EQ distance	25 feet (7 meters)
Formats	RGB and YCbCr digital video
Digital sampling	8, 10, 12 bits per channel
Standards	DVI 1.0, HDMI 2.0b, HDCP 2.2/1.x, CEA-861E
Video input
Number/signal type	2 single link HDMI (or DVI-D*)
Connectors	2 female HDMI type A
NOTE     *Appropriate HDMI to DVI-D cables or adapters are required for DVI signal input/output.
Video output
Connectors	1 local HDMI output, 1 female RJ-45 output
Termination standard	TIA/EIA T568B
Signal transmission distance	Up to 330' (100 m) using shielded twisted pair (STP) cable or XTP DTP 24 STP cable
Cable requirements	Solid conductor, 24 AWG or better
Cable recommendations	400 MHz bandwidth, STP (shielded twisted pair)
NOTE     Extron XTP DTP 24 shielded twisted pair cable is strongly recommended for optimal performance.
Audio
Gain	Unbalanced output: 0 dB; balanced output +6 dB
Frequency response	20 Hz to 20 kHz, ±0.5 dB
THD + Noise	0.03% @ 20 Hz to 20 kHz at maximum output
S/N	>90 dB, at maximum output (15 dBu), balanced (unweighted)
Stereo channel separation	>80 dB @ 1 kHz to 20 kHz
Audio input
Number/signal type	1 PC level stereo, unbalanced 2 Digital Embedded Audio on HDMI
NOTE     Analog audio can be configured for embedding onto the digital video signal at the Transmitter. Embedded digital audio can be (configured) de-embedded from the digital video signal at the Receiver end.
Connectors	(1) 3.5 mm stereo jack, 2 channel; tip (L), ring (R), sleeve (ground) (2) Female HDMI
Impedance	>10k ohms, DC coupled
Nominal level	-10 dBV (316 mVrms)
Maximum level	+7 dBV (unbalanced)
NOTE     0 dBu = 0.775 Vrms, 0 dBV = 1 Vrms, 0 dBV ? 2 dBu
Communications — switcher
Serial control port	1 RS-232, 3.5 mm, 3-pole captive screw connector, rear panel
Pin configuration	Pin 1 = Tx, Pin 2 = Rx, Pin 3 = GND
Baud rate and protocol	9600 baud, 8 data bits, 1 stop bit, no parity
Pin configuration	Pins 1 and 2 of captive screw connector shorted together enable auto-input switching.
USB control port	1 female mini USB, type B, front panel
USB standards	USB 2.0, high speed
Contact closure/tally output	(1) 3.5 captive screw connector, 3-pole (1) 3.5 captive screw connector, 4-pole
Pin configuration	Contact Closure - Pin 1 =Input 1 contact, Pin 1 = Input 2 contact, Pin 2 = GND (for both captive screw)
Pin configuration	Tally -  Pin 3 = Input 1 tally ground, Pin 3 =  Input 2 tally ground, Pin 4 = +5V (on Input 2 captive screw)
Program control	Extron Simple Instruction Set™ (SIS™)
Communications — external device (RS-232/IR over TP)
Quantity/type	(1) RS-232 and IR via (1) 3.5 mm 5-pole captive screw connector
Serial control pass-through ports	(1) Bidirectional RS-232
Output/DTP Rx	(1) RS-232 (1) 3.5 mm 5-pole captive screw connector (shared with IR port)
Baud rate and protocol	300 to 115200 baud 8 or 7 data bits 1 or 2 stop bits No parity (default), even or odd parity
Serial control pin configurations	Pin 1 = Tx, Pin 2 = Rx, Pin 3 = GND
IR control pass-through ports	(1) bidirectional TTL level (0 to 5V) modulated infrared control from 30 KHz to 60 kHz
Output/DTP Rx	(1) RS-232 (1) 3.5 mm 5-pole captive screw connector (shared with RS-232 port)
IR control pin configuration	Pin 3 = GND, Pin 4 = IR Tx, Pin 5 = IR Rx
General
Power supply	External Input: 100-240 VAC, 50-60 Hz Output: 12 VDC, 3 A, 36 Watts
Power consumption
Device	TBD watts, 12 VDC
Device and power supply	TBD watts, 12 VDC
Remote power capability	Supports one endpoint (DTP2 Rx)
NOTE     DTP2 devices can only send power to other DTP2 devices. DO NOT send power to DTP devices or they will be damaged.
Temperature/humidity	Storage: -40 to +158 °F (-40 to +70 °C) / 10% to 90%, noncondensing Operating: +32 to +122 °F (0 to +50 °C) / 10% to 90%, noncondensing
Cooling	Convection, vents on top and sides
Thermal dissipation
Device	TBD BTU/hr
Device and power supply	TBD BTU/hr
Mounting
Rack mount	Yes, with optional rack shelf Back of the rack mountable with optional back-of-the-rack mounting kit
Furniture mount	Yes, with optional under-desk mounting kit
Enclosure type	Metal
Enclosure dimensions	1.00" H x 8.75" W x 6.0" D (1 inch high, half rack wide) (2.54 cm H x 22.2 cm W x 15.2 cm D) (Depth excludes connectors.)
Product weight	TBD lb (TBD kg)
Regulatory compliance	CE, c-UL, UL, C-Tick, FCC Class A, ICES, RoHs, WEEE, VCCI
Product warranty	3 years parts and labor
Everlast power supply warranty	7 years parts and labor
NOTE     All nominal levels are at ±10%.
NOTE     Specifications are subject to change without notice.
(4238-D3)