FOX Tx AV

Technische Daten

FOX Tx AV
NOTE     The FOX Tx AV is a transmitter with one or two fiber optic cables linking it to a receiver.
NOTE     The analog video input signal is digitized pixel for pixel in the transmitter, sent digitally through the fiber cable, and converted back to analog video in the receiver.
NOTE     The analog audio signals are digitized in the transmitter, sent through the fiber cable, and converted back to analog audio in the receiver.
NOTE     The FOX AV transmitter is a class 1 laser product. It meets the safety regulations of IEC-60825.
Optical fiber interconnection between transmitter and receiver
Number/type	1 or 2 fiber optic
NOTE     Only one fiber is required to transmit video, audio, and unidirectional data. A second fiber is required to transmit return data for bidirectional control and communication.
Connectors	2 LC connectors
Operating distance
Singlemode	30 km (18.75 miles) with singlemode (SM) cables with a FOX Tx AV SM
Multimode	500 m (1640') with 62.5 µm multimode (MM) cables with a FOX Tx AV MM 1 km (3280') with 50 µm multimode cables with a FOX Tx AV MM 2 km (6561') with 50 µm, 2000 MHz bandwidth laser optimized multimode cables with a FOX Tx AV MM
NOTE     Operating distance is approximate. These are typical maximum distances that may vary depending on factors such as fiber type, fiber bandwidth, connector splicing, losses, modal or chromatic dispersion, environmental factors, and kinks.
Nominal peak wavelength	850 nm for FOX Tx AV MM, 1310 nm for FOX Tx AV SM
Data rate	2.125 Gbps
Transmission power	-5 dBm, typical
Maximum receiver sensitivity
Singlemode	-18 dBm, typical
Multimode	-12 dBm, typical
Optical loss budget
Singlemode	13 dB, maximum
Multimode	7 dB, maximum
Video
Gain	Unity
Standards
Input	NTSC 3.58, NTSC 4.43, PAL, SECAM, autodetected
Output	NTSC 3.58, PAL (follows vertical rate)
Decoder type	Adaptive 2D, digital comb filter
Video input
Number/signal type	1 component (Y, R-Y, B-Y), S-video, composite video
Connectors	1 x 3 female BNC or 1 female 4-pin mini DIN for S-video
Nominal level	1.0 Vp-p for Y of component video and S-video, and for composite video 0.7 Vp-p for R-Y, B-Y of component video 0.3 Vp-p for C of S-video
Minimum/maximum levels	Analog: 0.3 V to 1.5 Vp-p with no offset
Impedance	75 ohms
Return loss	-30 dB for Y/VID, B-Y/C, R-Y @ 5 MHz
Input coupling	AC
Audio
Gain
Range	Adjustable, -18 dB to +10 dB
Default	Unbalanced output: -6 dB; balanced output: 0 dB
Frequency response	20 Hz to 20 kHz, ±0.5 dB
THD + Noise	0.15% @ 1 kHz at nominal level
S/N	>80 dB at maximum output (unweighted)
CMRR	65 dB @ 20 Hz to 20 kHz
Audio bits per sample	18 bits per channel, 2 channels (L, R)
Sampling rate	48 kHz
Audio input
Number/signal type	1 stereo, balanced/unbalanced or 2 mono, balanced/unbalanced
Connectors	(1) 3.5 mm captive screw connector, 5 pole
Impedance	>10k ohms unbalanced, >20k ohms balanced, DC coupled
Nominal level	+4 dBu (1.23 Vrms), -10 dBV (316 mVrms)
Maximum level	+17 dBV, (unbalanced) at 1% THD+N
NOTE     0 dBu = 0.775 Vrms, 0 dBV = 1 Vrms, 0 dBV ? 2 dBu
Control/remote
Serial control ports on each unit (transmitter and receiver)
Control	1 RS-232, 3.5 mm captive screw connector, 5 pole (3 pins are used) (rear panel); in parallel with front panel jack 1 RS-232, 2.5 mm mini stereo jack (front panel)
Pass-through	1 RS-232, 3.5 mm captive screw connector, 5 pole (3 pins are used) (rear panel)
Baud rate and protocol
Control	9600 baud, 8 data bits, 1 stop bit, no parity
Pass-through	9600 to 115200 baud
Serial control pin configurations
Pass-through	Captive screw connector: 1 = Tx, 2 = Rx, 3 = GND
Control	Captive screw connector: 3 = GND, 4 = Tx, 5 = Rx Mini stereo jack: tip = Tx, ring = Rx, sleeve = GND
Program control	Extron control/configuration program for Windows® Extron Simple Instruction Set (SIS™)
General
Power supply	External Input: 100-240 VAC, 50-60 Hz Output: 12 VDC, 1 A, 12 watts
Power input requirements	12 VDC, 0.6 A
Temperature/humidity	Storage: -40 to +158 °F (-40 to +70 °C) / 10% to 90%, noncondensing Operating: +32 to +122 °F (0 to +50 °C) / 10% to 90%, noncondensing
Cooling	Convection, vents on left side and top
Mounting
Rack mount	Yes, with optional rack shelf kit
Furniture mount	Yes, with optional under-desk mounting kit
Enclosure type	Metal
Enclosure dimensions	1.7" H x 4.3" W x 6.0" D (1U high, quarter rack wide) (4.3 cm H x 10.9 cm W x 15.2 cm D) (Depth excludes connectors.)
Product weight	0.8 lbs (0.4 kg) per unit, 1.6 lbs (0.7 kg) per pair
Shipping weight	3 lbs (2 kg) per unit, 6 lbs (3 kg) per pair
Vibration	ISTA 1A in carton (International Safe Transit Association)
Regulatory compliance
Safety	CE, CUL, UL
EMI/EMC	CE, C-tick, FCC Class A, ICES, VCCI
Product warranty	3 years parts and labor
Everlast power supply warranty	7 years parts and labor
NOTE     All nominal levels are at ±10%.
NOTE     Specifications are subject to change without notice.
(8.1-112114-D2)

Versand-Abmessung und -Gewicht
Teilenummer	Höhe	Breite	Tiefe	Gewicht
60-941-11	10,5 cm	22,2 cm	31,2 cm	1,22 kg
60-941-12	10,5 cm	22,2 cm	31,2 cm	1,22 kg