FOXBOX Rx VGA

Technische Daten

FOXBOX Rx VGA
NOTE     The FOXBOX Rx VGA is a receiver with one or two fiber optic cables linking it to a transmitter. It is available in singlemode or multimode versions.
NOTE     The analog RGB input signal is digitized pixel for pixel in the transmitter, sent digitally through the fiber cable, and converted back to analog RGB in the receiver.
NOTE     The analog audio signals are digitized in the transmitter, sent through the fiber cable, and converted back to analog audio in the receiver.
NOTE     This receiver is a class 1 laser product. It meets the safety regulations of IEC-60825.
Optical fiber interconnection between transmitter and receiver
Number/type	1 or 2 fiber optic
NOTE     Only one fiber is required to transmit video, audio, and unidirectional data. A second fiber is required to transmit return data for bidirectional control and communication.
Connectors	2 LC connectors
Operating distance
Singlemode	30 km (18.75 miles) with singlemode (SM) cables with SM units
Multimode	300 m (985') with 62.5 µm OM1 multimode (MM) cables with MM units 1 km (3280') with 50 µm OM2 multimode (MM) cables with MM units 2 km (6561') with 50 µm OM3/OM4 2000 MHz bandwidth laser optimized multimode cable with MM units
NOTE     Operating distance is approximate. These are typical maximum distances that may vary depending on factors such as fiber type, fiber bandwidth, connector splicing, losses, modal or chromatic dispersion, environmental factors, and kinks.
Nominal peak wavelength	850 nm for MM, 1310 nm for SM
Data rate	4.25 Gbps
Transmission power	-5 dBm, typical
Maximum receiver sensitivity
Singlemode	-18 dBm, typical
Multimode	-12 dBm, typical
Optical loss budget
Singlemode	13 dB, maximum
Multimode	7 dB, maximum
Video
Signal type	VGA-UXGA RGBHV, RGBS, RGsB, RsGsBs
Gain	Unity
Pixel data bit depth	8 bits per channel, 3 channels (R, G, B; or YUV)
Resolution range	640x480 to 1600x1200 @ 60Hz or 480p, 576p, 720p, 1080i, 1080p @ 60 Hz pixel for pixel; higher resolutions up to 1920x1200 @ 60 Hz, undersampled
Video output
Number/signal type	With input from a FOXBOX Tx VGA: 1 VGA-UXGA RGBHV, RGsB (follows input or can be set by user) With input from a FOXBOX Tx VGA/YUV: 1 VGA-UXGA RGBHV, RGBS, component video (bi- or tri-level YUV, 480p, 576p, 720p, 1080i, 1080p)
Connectors	1 female 15 pin HD
Nominal level	1 Vp-p for Y or component video 0.7 Vp-p for RGB and R-Y and B-Y of component video
Minimum/maximum levels	0.3 V to 0.75 Vp-p, terminated
Impedance	75 ohms
Return loss	-30 dB @ 5 MHz
DC offset	±5 mV with input at 0 offset
Video delay	1-2 frames
Sync
Output type	RGBHV, RGsB (follows input or can be set by user)
Output level	TTL: 5.0 Vp-p, unterminated, on HV, for RGBHV, RGBS 0.3 Vp-p for component video (bi-level sync, unterminated) or for Gs (SOG), terminated 0.6 Vp-p for component video (tri-level sync)
Output impedance	75 ohms
Polarity	Positive or negative (follows input or can be set by user)
Audio
Gain
Range	Adjustable, -18 dB to +10 dB
Default	Unbalanced output: 0 dB
Frequency response	20 Hz to 20 kHz, ±0.5 dB
THD + Noise	0.10% @ 1 kHz at nominal level
S/N	>80 dB at maximum output (unweighted)
CMRR	65 dB @ 20 Hz to 20 kHz
Audio bits per sample	18 bits per channel, 2 channels (L, R)
Sampling rate	48 kHz
Audio output
Number/signal type	1 unbalanced stereo or 2 unbalanced mono
Connectors	(1) 3.5 mm mini stereo jack
Impedance	50 ohms unbalanced
Nominal level	-10 dBV (316 mVrms)
Maximum level (Hi-Z)	+7.6 dBu, unbalanced at 1% THD+N
Maximum level (600 ohm)	>+6.3 dBu, unbalanced at 1% THD+N
Audio delay	1.5 frames
Control/remote
Serial control ports on each unit (transmitter and receiver)
Control	1 RS-232, 2.5 mm mini stereo jack (front panel)
Pass-through	1 RS-232, 3.5 mm captive screw connector, 5 pole (3 pins are used) (rear panel)
Baud rate and protocol
Control	9600 baud, 8 data bits, 1 stop bit, no parity
Pass-through	9600 to 115,200 baud
Serial control pin configuration	Mini stereo jack: tip = Tx, ring = Rx, sleeve = GND
Program control	Extron control/configuration program for Windows® Extron Simple Instruction Set (SIS™)
General
Power supply	External Input: 100-240 VAC, 50-60 Hz Output: 12 VDC, 1 A, 12 watts
Power input requirements	12 VDC, 0.6 A
Temperature/humidity	Storage: -40 to +158 °F (-40 to +70 °C) / 10% to 90%, noncondensing Operating: +32 to +122 °F (0 to +50 °C) / 10% to 90%, noncondensing
Cooling	Convection, vents on top and side panels
Thermal dissipation	10.9 BTU/hr
Mounting
Rack mount	Yes, with optional rack shelf
Furniture mount	Yes, with optional under desk mounting kit
Enclosure type	Metal
Enclosure dimensions	1.0" H x 4.3" W x 6.0" D (quarter rack wide) (2.5 cm H x 10.9 cm W x 15.2 cm D) (Depth excludes connectors.)
Product weight	0.7 lbs (0.3 kg) per unit, 1.4 lbs (0.6 kg) per pair
Shipping weight	3 lbs (2 kg) per unit, 6 lbs (3 kg) per pair
Vibration	ISTA 1A in carton (International Safe Transit Association)
Regulatory compliance
Safety	CE, c-UL, UL
EMI/EMC	CE, C-tick, FCC Class A, ICES, VCCI
Product warranty	3 years parts and labor
Everlast power supply warranty	7 years parts and labor
NOTE     All nominal levels are at ±10%.
NOTE     Specifications are subject to change without notice.
(8.1-120914-D2)

Versand-Abmessung und -Gewicht
Teilenummer	Höhe	Breite	Tiefe	Gewicht
60-934-21	6,4 cm	31,3 cm	22,2 cm	1,12 kg
60-934-22	6,4 cm	31,3 cm	22,2 cm	1,12 kg