DTP T 3G-SDI 230 D

€ 1644.00

  • inkl. 20 % USt zzgl. Versandkosten
    zurzeit nicht lagernd:
    Lieferzeit 5-7 Tage*

    *Alle Lieferzeiten sind ungefähre Angaben und können von der tatsächlichen Lieferzeit abweichen!

Hersteller
Extron
Art.Nr.
60-1479-13
EAN
60-1479-13

Produktbeschreibung

Hauptmerkmale

  • Überträgt 3G-SDI-, HD-SDI- oder SDI- sowie Steuerungs- und analoge Audiosignale bis zu 70 m über ein geschirmtes CATx-Kabel
  • Akzeptiert 3G-SDI/HD-SDI/SDI-Signale bis zu 2,97 Gbps
  • Gepufferter 3G-SDI/HD-SDI/SDI-Durchschliff
  • Es wird nachdrücklich geschirmtes XTP DTP 24-Twisted Pair-Kabel von Extron für eine optimale Leistung empfohlen
  • Kompatibel mit geschirmtem CATx-Twisted Pair-Kabel
  • JITC-zertifiziert
Modell Beschreibung der Version Teilenummer
DTP T 3G-SDI 230 D 3G-SDI-Sender - Decorator-Format, Schwarz - 70 m 60-1479-12
DTP T 3G-SDI 230 D 3G-SDI-Sender - Decorator-Format, Weiß - 70 m 60-1479-13
DTP T 3G-SDI 330 D 3G-SDI-Sender - Decorator-Format, Weiß - 100 m 60-1479-53

Technische Daten

Technische Daten

DTP T 3G-SDI 230 D
Video
    Signal type  SDI: NTSC @ 59.94 Hz, PAL @ 50 Hz;
HD-SDI: 720p @ 25, 29.97, 30, 50, 59.94, 60 Hz; 1035i @ 50, 59.94, 60 Hz;
1080i @ 50, 59.94, 60 Hz; 1080p @ 24, 30 Hz;
3G-SDI: 1080p @ 50, 59.94, 60 Hz (4:2:2); 1080i @ 50, 59.94, 60 Hz (4:2:2);
720p @ 24, 25, 50, 59.94, 60 Hz (4:2:2)
    Data rates  270 Mbps, 1.485 Gbps, 2.97 Gbps
    Standards  SMPTE-259M, SMPTE-292M, SMPTE-424M, SMPTE-272M, SMPTE-299M, ITU-RBT.601,
ITU-RBT.1120
Video input
    Number/signal type  1 single link SDI, HD-SDI, or 3G-SDI digital component video
    Connectors  1 female BNC
    Equalization  Automatic, up to 300' (100 m) for 3G-SDI
Audio — pertaining to DTP
    Gain  Unbalanced output: 0 dB (from receiver), balanced output: +6 dB (from receiver)
    Frequency response  20 Hz to 20 kHz, ±1 dB
    THD + Noise  0.03% @ 1 kHz, 0.3% @ 20 kHz at nominal level
    S/N  >90 dB at maximum output (unweighted)
    Stereo channel separation  >80 dB
    Digital sampling rate  48 kHz
    Bit depth  16 bit
Audio input
    Number/signal type  1 stereo, unbalanced
    NOTE     Analog audio is not embedded onto the digital video signal. Analog audio and digital embedded audio are transmitted simultaneously and output on the receiver on two different connectors.
    Connectors  1 female, 3.5mm, stereo jack, 2 channel; tip (L), ring (R), sleeve (Gnd)
    Impedance  >10k ohms, DC coupled
    Nominal level  -10 dBV (316 mVrms)
    Maximum level  +7 dBV, unbalanced
    NOTE     0 dBu = 0.775 Vrms, 0 dBV = 1 Vrms, 0 dBV ? 2 dBu
Audio output
    Signal type  DTP 230
    Connector  1 female RJ-45
Interconnection between transmitter and receiver
    Connectors  1 female RJ-45 per unit for 1 cable connecting the transmitter and receiver
    Termination standards  TIA/EIA T568B
    DTP signal 
       Signal transmission distance  Up to 230' (70 m) using shielded twisted pair (STP) cable or XTP DTP 24 cable
       Cable requirements  Solid conductor, 24 AWG or better
       Cable recommendations  400 MHz bandwidth STP cable
    NOTE     Extron XTP DTP 24 shielded twisted pair cable is strongly recommended for optimal performance.
Communications — external device (RS-232/IR over TP)
    NOTE     Protocol is mirrored between the connected DTP 230 or DTP 330 endpoints and the "Over TP" ports on the
DTP T 3G-SDI 230 D. Signals from a control device pass into each "Over TP" port, are embedded with the DTP signal, and sent to the individual DTP 230 Tx or Rx endpoints for control of remote sink or source devices. The "Over TP" ports are simply pass-through connections to DTP endpoints.
    Serial control port  Bidirectional RS-232 control via (1) 3.5 mm, 5-pole captive screw connector
(connector is shared with IR control port)
    Baud rates  300 to 38.4k baud
    Protocol  Data bits = 8 or 7
Stop bits = 1 or 2
Parity = none
    Serial control pin configuration  Captive screw connectors: 1 = Tx, 2 = Rx, 3 = Gnd
    IR control port  Bidirectional IR control via (1) 3.5 mm, captive screw connector, 5-pole
(connector is shared with RS-232 control port)
TTL level (0 to 5 V) modulated infrared control from 30 kHz up to 60 kHz
    IR control pin configuration  3 = Gnd, 4 = IR Tx, 5 = IR Rx
    USB control port  1 front panel female mini USB B
    USB standards  USB 2.0, low speed
    Program control  Extron Simple Instruction Set (SIS™)
General
    Power supply  External
Input: 100-240 VAC, 50-60 Hz
Output: 12 VDC, 1.5 A, 18 watts
    Power consumption 
       Device  8.9 watts, 12 VDC
       Device and power supply  10.8 watts, 100-240 VAC, 50-60 Hz
    NOTE     Each transmitter or receiver can be powered either locally by an external power supply or remotely by receiver or transmitter on the other end of the twisted pair cable.
    Temperature/humidity  Storage: -40 to +158 °F (-40 to +70 °C) / 10% to 90%, noncondensing
Operating: +32 to +122 °F (0 to +50 °C) / 10% to 90%, noncondensing
    Cooling  Convection, no vents
    Thermal dissipation 
       Device  12.5 BTU/hr
       Device and power supply  19.1 BTU/hr
    Mounting 
       Furniture or wall mount  Yes, with a 1 gang wall box or mud ring
    Enclosure type  Metal
    Enclosure dimensions 
       Faceplate  2.6" H x 1.3" W x 0.1 " D
(6.6 cm H x 3.3 cm W x 0.3 cm D)
       Device  2.7" H x 1.7" W x 1.6" D
(6.9 cm H x 4.3 cm W x 4.0 cm D)
    Product weight  1 lbs (0.5 kg)
    Regulatory compliance  AS/NZS, c-UL, C-tick, CE**, FCC Class A**, ICES, UL
    NOTE     **CE and FCC testing is conducted with STP cable.
    Product warranty  3 years parts and labor
    Everlast power supply warranty  7 years parts and labor
    NOTE     All nominal levels are at ±10%.
    NOTE     Specifications are subject to change without notice.
    NOTE     Shipping dimensions and weights are available at www.extron.com.
(4380-092818)
Versand-Abmessung und -Gewicht
    Teilenummer Höhe Breite Tiefe Gewicht
    60-1479-12 7,5 cm 26,7 cm 19,1 cm 0,73 kg
    60-1479-13 7,5 cm 26,7 cm 19,1 cm 0,73 kg