IPCP Pro 255

Technische Daten

IPCP Pro 255
Memory
SDRAM	512 MB
Flash	4.5 GB
Software and control options
Software	Extron Global Configurator® Plus and Professional for Windows®, Global Scripter®
Control options	GlobalViewer®, Extron Control for iPad and Web, TouchLink® Pro touchpanels, or eBUS® button panels
Ethernet control
Network interface controllers (NICs)	2: 1 LAN, 1 AV LAN
Connectors	2 female RJ-45 connectors
Data rate	10/100/1000Base-T, half/full duplex with autodetect
Protocols	DHCP, DNS, HTTP, HTTPS, ICMP, NTP, SFTP, SMTP, SNMP, SSH, TCP/IP, UDP/IP
Default settings
LAN	Link speed and duplex level = autodetected IP address = 192.168.253.250 Subnet mask = 255.255.255.0 Gateway = 0.0.0.0 DHCP = off DNS: 127.0.0.1
AV LAN	Link speed and duplex level = autodetected DHCP server = disabled Subnet mask = 255.255.255.0 Gateway = 0.0.0.0
DHCP server disabled	IP address = 192.168.254.250 DNS = 127.0.0.1
DHCP server enabled	IP address = 192.168.254.1 DNS = 192.168.254.1 Dynamic leased IP address pool = 192.168.254.100 - 192.168.254.149 Maximum lease count = 50 Lease time = 24 hours
Serial control
Quantity/type	1 bidirectional RS-232, RS-422, RS-485 (port 1) 1 bidirectional RS-232 (port 2)
Connector	(1) 3.5 mm captive screw connector, 5 pole (1) 3.5 mm captive screw connectors, 3 pole
Baud rate and protocol	300 to 115200 baud (9600 baud = default); 8 (default) or 7 data bits; 1 (default) or 2 stop bits; no parity (default), even, or odd parity
NOTE     The 5-pole ports support both hardware and software flow control. The 3-pole ports support software flow control. The default for both types of ports is no flow control.
Pin configurations
Serial, 5-pole captive screw
RS-232 (default)	Pin 1 = Tx, 2 = Rx, 3 = Gnd, 4 = RTS, 5 = CTS
RS-422	Pin 1 = Tx-, 2 = Rx-, 3 = Gnd, 4 = Tx+, 5 = Rx+
RS-485	Pins 1 and 2 (tied together) = data-, 3 = Gnd, 4 and 5 (tied together) = data+
Serial, 3-pole captive screw	Pin 1 = Tx, 2 = Rx, 3 = Gnd
Digital I/O control
Quantity/type	4 digital input/output (configurable)
Connectors	(1) 3.5 mm captive screw connector, 5 pole
Digital inputs
Input voltage range	0 to 24 VDC, clamped at +30 VDC
Input impedance	>10k ohms
Programmable pullup	1k ohms to +5 VDC
Threshold low to high	>2.8 VDC
Threshold high to low	<2.0 VDC
Digital outputs	250 mA sink from 24 VDC max.
Pin configurations	1, 2, 3, 4 = digital I/Os 1, 2, 3, 4; 5 = Gnd
IR/serial control
Quantity/type	1 programmable: unidirectional RS-232 (±5 V), or TTL level (0 to 5 V) infrared (carrier and non-carrier) up to 300 kHz
Connector	(1) 3.5 mm captive screw connector, 2-pole
Baud rate and protocol (RS-232)	300 to 115200 baud (9600 baud = default); 8 (default) or 7 data bits; 1 (default) or 2 stop bits; no parity (default), even, or odd parity
Pin configurations	For each port, pin 1 = signal, 2 = Gnd
IR output carrier frequency	30 kHz to 300 kHz
IR learning carrier frequency	30 kHz to 300 kHz
IR learning capture distance	2" (5.1 cm) to 12" (30.5 cm) from the front panel
Relay control
Quantity/type	2 normally open relays
Connector	(1) 3.5 mm captive screw connector, 3 pole
Relay control contact rating	24 VDC, 1 A
Volume control
Quantity/type	1 volume control (compatible with select Extron amplifiers)
Connectors	(1) 3.5 mm captive screw connector, 5 pole
Pin configuration	Pin 3 = ?10 VDC reference voltage input, pin 4 = 0 to +10 VDC control voltage output, pin 5 = Gnd
Control voltage output range	0 to +10 VDC (±0.2 volts), adjustable
eBUS control
eBUS control ports	(1) 3.5 mm captive screw connector, 5 pole (uses 4 poles)
eBUS pin configuration	+V = +12 VDC; +S = + signal; -S = - signal; G = ground
Recommended cable type	Extron STP20-2/1000 or STP20-2P/1000 cable
Maximum system cable length	1000 feet (305 meters) sum total for the eBUS system, regardless of topology. Power injection may be required depending on system cabling topology and primary power supply wattage. See the eBUS Technology Reference Guide for details.
eBUS power output	6 watts
General
Power supply	External Input: 100-240 VAC, 50-60 Hz Output: 12 VDC, 1 A, 12 watts
Power input requirements	12 VDC, 1 A, 12 watts, max.
Power consumption
Device	9.0 watts, 12 VDC
Device and power supply	11.9 watts, 100-240 VAC, 50-60 Hz
Temperature/humidity	Storage: -40 to +158 °F (-40 to +70 °C) / 10% to 90%, noncondensing Operating: +32 to +122 °F (0 to +50 °C) / 10% to 90%, noncondensing
Cooling	Convection, no vents
Thermal dissipation
Device	10.1 BTU/hr
Device and power supply	20.1 BTU/hr
Mounting
Rack mount	Yes, with optional 1U rack shelf
Furniture mount	Yes, with optional bracket kit
Enclosure type	Metal
Enclosure dimensions	1.7" H x 4.3" W x 6.0" D (1U high, quarter rack wide) (4.3 cm H x 10.9 cm W x 15.2 cm D) (Depth excludes connectors.)
Product weight	0.7 lbs (0.3 kg)
Vibration	ISTA 1A in carton (International Safe Transit Association)
Regulatory compliance
Safety	CE, c-UL, UL UL Listed for use in plenum air handling spaces
EMI/EMC	CE, C-Tick, FCC Class A, ICES, VCCI
Environmental	Complies with the appropriate requirements of RoHS, WEEE
Product warranty	3 years parts and labor
Everlast power supply warranty	7 years parts and labor
NOTE     All nominal levels are at ±10%.
NOTE     Specifications are subject to change without notice.
(4145-D3-110117)

Versand-Abmessung und -Gewicht
Teilenummer	Höhe	Breite	Tiefe	Gewicht
60-1431-01	7,5 cm	26,7 cm	19,1 cm	0,92 kg