MTPX Plus 128

Technische Daten

MTPX Plus Series
Video
Routing
MTPX Plus 816	8 x 16 matrix, 3 x 1 local
MTPX Plus 128	12 x 8 matrix, 4 x 2 local
MTPX Plus 168	16 x 8 matrix, 3 x 1 local
MTPX Plus 1616	16 x 16 matrix, 3 x 1 local
MTPX Plus 1632	16 x 32 matrix, 6 x 2 local
MTPX Plus 3216	32 x 16 matrix, 6 x 2 local
MTPX Plus 3232	32 x 32 matrix, 6 x 2 local
Gain	Unity ±1 dB
Crosstalk
128 models	-76 dB @ 1 MHz, -55 dB @ 10 MHz, -45 dB @ 30 MHz, -30 dB @ 100 MHz
816, 168, 1616 models	-80 dB @ 1 MHz, -71 dB @ 5 MHz, -55 dB @ 10 MHz, -45 dB @ 30 MHz, -37 dB @ 100 MHz
1632, 3216, 3232 models	-90 dB @ 1 MHz, -76 @ 5 MHz, -72 dB @ 10 MHz, -60 dB @ 30 MHz, -50 dB @ 100 MHz
Switching speed	200 ms (max.)
Video input — local
Number/signal type	3, 4, or 6 analog RGBHV, RGBS, RGsB, RsGsBs, component video (bi-level and tri-level), S-video, composite video
Connectors	3, 4, or 6 female 15-pin HD
Nominal level	1 Vp-p for Y of component video and S-video, and for composite video 0.7 Vp-p for RGB and for R-Y and B-Y of component video 0.3 Vp-p for C of S-video
Impedance	75 ohms ±5%
Horizontal frequency	15 kHz to 130 kHz
Vertical frequency	30 Hz to 150 Hz
Return loss	<-30 dB @ 5 MHz
DC offset (max. allowable)	250 mV
Video input — main (see transmitters' output specifications)
Number/signal type	8, 16, or 32 proprietary analog signals
Connectors	8, 16, or 32 (depending on configuration) female RJ-45 connectors
Video output — local
Number/signal type	1 or 2 analog RGBHV, RGBS, RGsB, RsGsBs, component video (bi-level and tri-level sync), S-video, composite video
Connectors	1 or 2 female 15-pin HD
Nominal level	0.7 Vp-p for RGB
Impedance	75 ohms ±10%
Return loss	<-30 dB @ 5 MHz
DC offset	<±40 mV with input at 0 offset
Video output — main (see receivers' input specifications)
Number/signal type	8, 16, or 32 proprietary analog signals
Connectors	8, 16, or 32 (depending on configuration) female RJ-45 connectors
Sync — local inputs and outputs only
Input type	RGBHV, RGBS, RGsB, RsGsBs
Output type	See receiver specifications (on Web site).
Standards	NTSC 3.58, NTSC 4.43, PAL, SECAM
Input level	3.5 V to 5.0 Vp-p, DC
Output level	See receiver specifications (on Web site).
Input impedance	611 ohms ±5%
Output impedance	105 ohms ±30 ohms
Max. output voltage	?4.0 VDC with a 2k ohm load
Max. rise/fall time	4 ns
Polarity	Positive or negative
Audio
Routing
MTPX Plus 816	8 x 16 mono matrix, 3 x 4 local
MTPX Plus 128	12 x 8 mono matrix, 4 x 2 local
MTPX Plus 168	16 x 8 mono matrix, 3 x 4 local
MTPX Plus 1616	16 x 16 mono matrix, 3 x 4 local
MTPX Plus 1632	16 x 32 mono matrix, 6 x 8 local
MTPX Plus 3216	32 x 16 mono matrix, 6 x 8 local
MTPX Plus 3232	32 x 32 mono matrix, 6 x 8 local
Gain (local inputs and outputs)	Unbalanced output: 0 dB ±2 dB with a 600 ohm load, single ended Balanced output: +6 dB ±2 dB with a 600 ohm load, single ended
Frequency response	20 Hz to 20 kHz, ±1 dB
THD + Noise	?0.15% @ 1 kHz at nominal level
S/N	>70 dB at maximum output (unweighted)
CMRR	>43 dB @ 20 Hz to 20 kHz
Audio input — local
Number/signal type	3, 4, or 6 stereo, balanced/unbalanced
Connectors	(3, 4, or 6) 3.5 mm captive screw connectors, 5 pole
Impedance	>10k ohms unbalanced
Nominal level	+4 dBu (1.23 Vrms), -10 dBV (316 mVrms)
Maximum level	+18 dBu, (unbalanced) at 1% THD+N
NOTE     0 dBu = 0.775 Vrms, 0 dBV = 1 Vrms, 0 dBV ? 2 dBu
Audio input — main (see transmitters' output specifications)
Number/signal type	8, 16, or 32 proprietary analog signals
Connectors	8, 16, or 32 (depending on configuration) female RJ-45 connectors
Audio output — local
Number/signal type	2, 4, or 8 dual mono, balanced/unbalanced
Connectors	(2, 4, or 8) 3.5 mm captive screw connectors, 5 pole
Impedance	50 ohms unbalanced, 100 ohms balanced ±10%
Gain error	±2 dB channel to channel
Maximum level (?10k ohms)	+16 dBu, balanced or unbalanced at 1% THD+N
Maximum level (600 ohm)	+15 dBm, balanced or unbalanced at 1% THD+N
Audio output — main (see receivers' input specifications)
Number/signal type	8, 16, or 32 proprietary analog signals
Connectors	8, 16, or 32 (depending on configuration) female RJ-45 connectors
Control/remote — switcher host control
Serial host control ports
MTPX Plus 128	1 RS-232, rear panel 3.5 mm captive screw connector, 3 pole
All other models	1 RS-232 or RS-422, rear panel female 9-pin D connector 1 RS-232 front panel 2.5 mm mini stereo jack
Baud rate and protocol	9600 baud (default), 19200, 38400, and 115200 (adjustable); 8 data bits; 1 stop bit; no parity
Serial control pin configurations
9-pin female D connector	RS-232: 2 = Tx, 3 = Rx, 5 = GND RS-422: 2 = Tx-, 3 = Rx-, 5 = GND, 7 = Rx+, 8 = Tx+
Mini stereo jack	Tip = Tx, ring = Rx, sleeve = GND
Captive screw connector	RS-232: 1 = Tx, 2 = Rx, 3 = GND
USB control ports
MTPX Plus 128	1 front panel female mini USB B
USB standards
MTPX Plus 128	USB 2.0, low speed
Ethernet control port	1 RJ-45 female connector
Ethernet data rate	10/100Base-T, half/full duplex with autodetect
Ethernet protocol	ARP, ICMP (ping), IP, TCP, UDP, DHCP, HTTP, SMTP, Telnet
Default settings	Link speed and duplex level = autodetected IP address = 192.168.254.254 Subnet mask = 255.255.0.0 Gateway = 0.0.0.0 DHCP = off
Web server	Up to 200 simultaneous sessions 16 MB nonvolatile user memory
Program control	Extron control/configuration program for Windows® Extron Simple Instruction Set™ (SIS™) Microsoft® Internet Explorer® version 6 or higher, Telnet
Control/remote — external device (pass-through, unidirectional, or bidirectional)
Serial control ports	RS-232, 3.5 mm captive screw connectors, 3 pole
3232 and 1632 models	16 connectors
3216, 1616, 128, and 816 models	8 connectors
168 models	4 connectors
Baud rate and protocol	Up to 38400 baud, 9600 baud (default); 5-8 data bits; 1 or 2 stop bits; odd, even, or no parity; XON, XOFF, or no flow control
NOTE     Protocol is mirrored between the switcher and the receiver.
Serial control pin configurations	1 = Tx, 2 = Rx, 3 = GND
General
Recommended cable type	Shielded or unshielded CAT 5/5e/6/7 or Extron Enhanced Skew-Free™ A/V UTP
Power	100 VAC to 240 VAC, 50-60 Hz, internal
1632, 3216, 3232 models	220 watts
816, 168, 1616 models	120 watts
128 model	73 watts
Temperature/humidity	Storage: -40 to +158 °F (-40 to +70 °C) / 10% to 90%, noncondensing Operating: +32 to +122 °F (0 to +50 °C) / 10% to 90%, noncondensing
Cooling	Fan, left to right (as viewed from the front panel)
Thermal dissipation
128 model
115 VAC, 60 Hz	231.1 BTU/hr
240 VAC, 50 Hz	223.8 BTU/hr
1616 model
115 VAC, 60 Hz	348.3 BTU/hr
240 VAC, 50 Hz	353.0 BTU/hr
3232 model
115 VAC, 60 Hz	607.1 BTU/hr
240 VAC, 50 Hz	595.3 BTU/hr
Rack mount	Yes
Enclosure type	Metal
Enclosure dimensions	Depth excludes connectors, width excludes rack ears.
1632, 3216, 3232 models	5.25" H x 17.0" W x 9.4" D (3U high, full rack wide) (13.3 cm H x 43.1 cm W x 23.9 cm D)
816, 168, 1616 models	3.5" H x 17.0" W x 9.4" D (2U high, full rack wide) (8.9 cm H x 43.1 cm W x 23.9 cm D)
128 model	1.7" H x 17.4" W x 12.0" D (1U high, full rack wide) (4.3 cm H x 44.2 cm W x 30.5 cm D)
Product weight
1632, 3216, 3232 models	16.0 lbs (7.3 kg)
816, 168, 1616 models	8.5 lbs (3.9 kg)
128 model	3.7 lbs (1.6 kg)
Shipping weight
1632, 3216, 3232 models	26 lbs (ll.8 kg)
816, 168, 1616 models	18 lbs (9 kg)
128 model	7 lbs (4 kg)
DIM weight (International)
1632, 3216, 3232 models	26 lbs (11.8 kg)
816, 168, 1616 models	18 lbs (9 kg)
128 model	7 lbs (4 kg)
Vibration	ISTA 1A in carton (International Safe Transit Association)
Regulatory compliance
Safety	CE, c-UL, UL
EMI/EMC	CE, C-tick, FCC Class A, ICES, VCCI Class A
Environmental	Complies with the appropriate requirements of WEEE.
Product warranty	3 years parts and labor
Everlast power supply warranty	7 years parts and labor
NOTE     All nominal levels are at ±10%.
NOTE     Specifications are subject to change without notice.
(7.6-021910-D16)

Versand-Abmessung und -Gewicht
Teilenummer	Höhe	Breite	Tiefe	Gewicht
60-1015-01	54,0 cm	39,4 cm	10,2 cm	4,24 kg