MTP/HDMI U R

Technische Daten

MTP/HDMI U R
Video
MTP input
Gain	Unity
Maximum resolution
Analog	Up to 2048x1080 or 1080p @ 60 Hz
Signal transmission distance, analog
HDMI digital input
Maximum data rate	4.95 Gbps (1.65 Gbps per color)
Maximum pixel clock	165 MHz
Maximum resolution
Digital	Up to 1920x1200 or 1080p @ 60 Hz
Signal transmission distance, digital
NOTE     The transmission distance varies greatly depending on the signal resolution and on the type of cable, graphics card, and display used in the system.
NOTE     Shielded twisted pair cable provides added protection from outside interference and increases overall signal transmission distance. Extron strongly recommends using shielded twisted pair for optimal performance.
Formats	RGB and YCbCr digital video
Standards	DVI 1.0, HDMI 1.2
Video input
Number/signal type
MTP input	1 set of proprietary analog signals
HDMI digital input	1 set of proprietary digital signals
Connectors
MTP input	1 female RJ-45
HDMI digital input	2 female RJ-45
Video output
Number/signal type
Analog output	1 RGBHV, RGBS, component video (bi-level and tri-level), S-video, composite video (follows input type)
HDMI digital output	1 single link HDMI (or DVI-D*)
NOTE     *Appropriate HDMI to DVI-D cables or adapters are required for DVI signal input/output.
Connectors
Analog output	1 female 15-pin HD for RGB 3 female BNC for Y, R-Y, B-Y 1 female 4-pin mini DIN for S-video (Y/C) 1 female BNC for composite video
HDMI digital output	1 female HDMI type A
Nominal levels	Analog outputs: 1 Vp-p for Y of component video and S-video, and for composite video 0.7 Vp-p for RGB and for R-Y and B-Y of component video 0.3 Vp-p for C of S-video
Minimum/maximum levels	Analog outputs: 0.8 V to 1.2 Vp-p
Impedance	Analog outputs: 75 ohms (during video output only)
Return loss	Analog outputs: <-30 dB @ 5 MHz (during video output only)
DC offset	Analog outputs: <±20 mV with input at 0 offset
Sync — analog outputs
Output type	RGBHV, RGBS, component video (bi- or tri-level)
Standards	NTSC 3.58, NTSC 4.43, PAL, SECAM
Output level	4.0 V to 5.0 Vp-p, unterminated
Output impedance	87 ohms (24 mA)
Polarity	Positive or negative (selectable)
Audio — from MTP input
Gain	Unbalanced output: 0 dB; balanced output: +6 dB
Frequency response	20 Hz to 20 kHz, ±1 dB
THD + Noise	0.15% @ 1 kHz, 0.3% @ 20 kHz at nominal level
S/N	>70 dB at maximum output (unweighted)
Audio input — from MTP input, see MTP transmitter's audio output specifications
Number/signal type	1 set of proprietary analog signals
Connectors	1 female RJ-45
NOTE     0 dBu = 0.775 Vrms, 0 dBV = 1 Vrms, 0 dBV ? 2 dBu
Audio output — from MTP input
Number/signal type	2 mono, balanced/unbalanced
Connectors	(1) 3.5 mm captive screw connector, 5 pole
Impedance	50 ohms unbalanced, 100 ohms balanced
Gain error	±1 dB channel to channel
Control/remote — external device (pass-through) from the HDMI input
Serial control port input/output	RS-232 via (1) 3.5 mm, 3 pole captive screw connector
Serial control pin configuration	Captive screw connector: 1 = Tx, 2 = Rx, 3 = GND
Control/remote — external device (pass-through, unidirectional or bidirectional) from the MTP input
Serial control port input/output	RS-232 via (1) 3.5 mm, 5 pole captive screw connector (3 poles are used)
Baud rates	Up to 38400 bps at up to 600' (183 m) (Higher data rates and distances are possible. Performance varies based on baud rate and cable length.)
Protocol	Data bits = 5 - 8 Stop bits = 1 or 2 Parity = odd, even, none Flow control = XON, XOFF, none
NOTE     Protocol is mirrored between the transmitter and the receiver.
Serial control pin configuration	Captive screw connector: 1 = Tx, 2 = Rx, 3 = GND
General
Recommended cable type	Shielded or unshielded
MTP input	CAT 5/5e/6
HDMI digital input	CAT 5/5e/6, Extron STP201
NOTE     Shielded twisted pair cable provides added protection from outside interference and increases overall signal transmission distance. Extron strongly recommends using shielded twisted pair for optimal performance.
Power supply	External Input: 100-240 VAC, 50-60 Hz Output: 12 VDC, 1 A, 12 watts
Power input requirements	12 VDC, 0.8 A
Temperature/humidity	Storage: -40 to +158 °F (-40 to +70 °C) / 10% to 90%, noncondensing Operating: +32 to +122 °F (0 to +50 °C) / 10% to 90%, noncondensing
Cooling	Convection, no vents
Thermal dissipation	18.1 BTU/hr
Mounting
Rack mount	Yes, with optional 1U rack shelf
Furniture mount	Yes, with optional under-desk mounting kit
Pole mount	Yes, with optional projector mounting kit
Enclosure type	Metal
Enclosure dimensions	1.7" H x 8.75" W x 3.0" D (half rack wide) (4.3 cm H x 22.2 cm W x 7.6 cm D) (Depth excludes connectors.)
Product weight	0.8 lbs (0.4 kg)
Shipping weight	2 lbs (1 kg)
Vibration	ISTA 1A in carton (International Safe Transit Association)
Regulatory compliance
Safety	CE, c-UL, UL UL rated for use in plenum airspaces: meets UL 2043 for heat and smoke release, excluding the power supply.
EMI/EMC	CE, C-tick, FCC Class A, ICES, VCCI
Product warranty	3 years parts and labor
NOTE     All nominal levels are at ±10%.
NOTE     Specifications are subject to change without notice.
(8.0-060811-D14)

Versand-Abmessung und -Gewicht
Teilenummer	Höhe	Breite	Tiefe	Gewicht
60-1048-01	6,8 cm	18,1 cm	24,1 cm	0,92 kg