MTP R 15HD RSA D

Technische Daten

MTP R 15HD RSA D
Video
Gain	Unity
Number/signal type	1 set of proprietary analog signals
Connectors	1 female RJ-45 on a pigtail
Video input — See MTP Series Transmitter video output specifications
Video output
Number/signal type	1 analog VGA-UXGA RGBHV, RGBS, RGsB, RsGsBs, HD component video, component video, S-video, or composite video
Connectors	1 female 15-pin HD
Nominal level	1 Vp-p for Y of component video and S-video, and for composite video 0.7 Vp-p for RGB and for R-Y and B-Y of component video 0.3 Vp-p for C of S-video
Minimum/maximum levels	0.3 V to 1.45 Vp-p
Impedance	75 ohms
Return loss	<-30 dB @ 5 MHz
DC offset	<±20 mV with input at 0 offset
Maximum resolution	1920x1200 or 2048x1080
NOTE     Refer to the user guide for the maximum distances recommended for specific resolutions.
Sync
Output type	RGBHV, RGBS, RGsB, RsGsBs
Standards	NTSC 3.58, NTSC 4.43, PAL, SECAM
Output level	4.0 V to 5.0 Vp-p, unterminated
Output impedance	110 ohms
Polarity	Positive or negative (switch selectable)
Audio
Number/signal type	1 set of proprietary analog signals from an MTP transmitter
Connector	1 female RJ-45
Gain	Unbalanced output: 0 dB; balanced output: +6 dB
Frequency response	20 Hz to 20 kHz, ±1 dB
THD + Noise	0.15% @ 1 kHz, 0.3% @ 20 kHz at nominal level
S/N	>70 dB at maximum output (unweighted)
CMRR	>43 dB @ 20 Hz to 20 kHz
Audio output
Number/signal type	1 mono, balanced/unbalanced
Connector	(1) 3.5 mm captive screw connector, 5 pole (uses 3 poles)
Impedance	50 ohms balanced, 100 ohms balanced
Gain error	±1 dB channel to channel
Nominal level	+4 dBu (1.23 Vrms), -10 dBV (316 mVrms)
Maximum level	14 dBm, unbalanced at 1% THD+N
Control/remote — external device (pass-through, unidirectional or bidirectional)
Serial control port input/output	1 set of proprietary signals on a female RJ-45 jack
Serial control port output/input	RS-232 via 3 poles of a 3.5 mm captive screw connector, 5 pole
NOTE     The serial communications link is unidirectional only, transmitter to receiver, unless the  directional DIP switch of the receiver has been repositioned. The switch should be repositioned only when the receiver is the only one in the system.
Baud rates	Up to 38400 bps at up to 1000' (304.8 m) (Higher data rates and distances are possible. Performance varies based on baud rate and cable length.)
Protocol	Data bits = 5 - 8 Stop bits = 1 or 2 Parity = odd, even, none Flow control = XON, XOFF, none
NOTE     Protocol is mirrored between the transmitter and the receiver.
Serial control pin configuration	Captive screw connector: 1 = Tx, 2 = Rx, 3 = GND
General
Recommended cable type	CAT5/5E/6 (shielded or unshielded)
Power supply	External Input: 100-240 VAC, 50-60 Hz Output: 12 VDC, 1 A, 12 watts
Power input requirements	12 VDC, 0.5 A
Temperature/humidity	Storage: -40 to +158 °F (-40 to +70 °C) / 10% to 90%, noncondensing Operating: +32 to +122 °F (0 to +50 °C) / 10% to 90%, noncondensing
Cooling	Convection, no vents
Mounting
Furniture mount	Yes, using a standard electrical wall box or Decorator-Style size mud ring
Enclosure type	Metal
Enclosure dimensions
Faceplate	2.6" H* x 1.3" W x 0.24" D (6.6 cm H* x 3.3 cm W x 0.5 cm D) *Height is 3.8" (9.7 cm) including mounting tabs. (Fits the opening in a 1 gang, 4.4" H x 2.7" W Decorator-Style wallplate. Depth excludes connectors.)
Device	2.75" H x 1.65" W x 1.3" D (7.0 cm H x 4.2 cm W x 3.3 cm D) (Depth excludes connectors.)
Product weight	0.4 lbs (0.2 kg)
Vibration	ISTA 1A in carton (International Safe Transit Association)
Regulatory compliance
Safety	CE, c-UL, UL
EMI/EMC	CE, C-tick, FCC Class A, ICES, VCCI
Product warranty	3 years parts and labor
Everlast power supply warranty	7 years parts and labor
NOTE     All nominal levels are at ±10%.
NOTE     Specifications are subject to change without notice.
(4007-041917)

Versand-Abmessung und -Gewicht
Teilenummer	Höhe	Breite	Tiefe	Gewicht
60-929-02	7,0 cm	22,9 cm	34,3 cm	0,77 kg
60-929-01	7,0 cm	22,9 cm	34,3 cm	0,84 kg