MTP RL 15HD RS und MTP RL 15HD RS SEQ

Technische Daten

MTP 15HD RS Series
Video
Gain	Unity
Number/signal type
MTP 4T 15HD RS	4 sets of proprietary analog signals
All other models	1 set of proprietary analog signals
Connectors
MTP 4T 15HD RS	4 female RJ-45
MTP R 15HD RSA D	1 female RJ-45 on a pigtail
All other models	1 female RJ-45
Video input and loop-through — transmitter (MTP T 15HD RS, MTP C7 T 15HD RS, MTP 4T 15HD RS)
Number/signal type	1 analog RGBHV, RGBS, RGsB, RsGsBs, component video (with bi-level or tri-level sync), S-video, or composite video 1 buffered RGBHV, RGBS, RGsB, RsGsBs local monitor loop through (includes ID bits)
Connectors	2 female 15-pin HD
Nominal level	1 Vp-p for Y of component video and S-video, and for composite video 0.7 Vp-p for RGB and for R-Y and B-Y of component video 0.3 Vp-p for C of S-video
Minimum/maximum levels	0.3 V to 1.45 Vp-p
Impedance	75 ohms
Horizontal frequency	15 kHz to 130 kHz
Vertical frequency	30 Hz to 150 Hz
Return loss	<-30 dB @ 5 MHz
DC offset (max. allowable)	250 mV
Video output — receivers
Number/signal type
MTP R 15HD RSA D	1 analog VGA-UXGA RGBHV, RGBS, RGsB, RsGsBs, HD component video, component video, S-video, or composite video
All other receivers	1 set of proprietary analog signals 1 analog RGBHV, RGBS, RGsB, RsGsBs, component video (bi-/tri-level sync), S-video, or composite video
Connectors
MTP R 15HD RSA D	1 female 15-pin HD
All other receivers	1 female RJ-45 1 female 15-pin HD
Nominal level	1 Vp-p for Y of component video and S-video, and for composite video 0.7 Vp-p for RGB and for R-Y and B-Y of component video 0.3 Vp-p for C of S-video
Minimum/maximum levels	0.3 V to 1.45 Vp-p
Impedance	75 ohms
Return loss	<-30 dB @ 5 MHz
DC offset	<±20 mV with input at 0 offset
Skew compensation	62 ns
Maximum resolution
MTP 1500RL 15HD models	Up to 1600x1200 and 1080p at 1500' Up to 1920x1200 and 2048x1080 at 1200'
All other models	Up to 1920x1200 or 2048x1080 or 1080p at 300' Up to 1024x768 at 600'
NOTE     Refer to the user's manual for the maximum distances recommended for specific resolutions.
Sync
Input type (transmitter)	RGBHV, RGBS, RGsB, RsGsBs
Output type (receivers)	RGBHV, RGBS, RGsB, RsGsBs
Standards	NTSC 3.58, NTSC 4.43, PAL, SECAM
Input level (transmitter)	3.5 V to 5.5 Vp-p, unterminated
Output level (receivers)
MTP 1500RL 15HD models	0.3 Vp-p for component video (bi-level sync) 0.6 Vp-p for component video (tri-level sync) TTL: 4.0 V to 5.0 V p-p, unterminated for RGBHV, RGBS
All other models	4.0 V to 5.0 Vp-p, unterminated
Input impedance
MTP C7 models	573 ohms
All other models	510 ohms
Output impedance
MTP C7 models	92 ohms ±8% (25 mA)
All other models	110 ohms
Polarity
Transmitter	Positive or negative (follows input polarity)
Receivers	Positive or negative (switch selectable)
Control/remote — external device (pass-through, unidirectional or bidirectional)
Serial control port input/output
MTP T 15HD RS, MTP C7 T 15HD RS, MTP 4T 15HD RS	RS-232 via (1) 3.5 mm, 3 pole captive screw connector
MTP R 15HD RSA D, MTP C7 RL 15HD RS, MTP C7 RL 15HD RS SEQ	1 set of proprietary signals on a female RJ-45 jack
Serial control port output/input
MTP T 15HD RS, MTP C7 T 15HD RS, MTP 4T 15HD RS	1 set of proprietary signals on a female RJ-45 jack
MTP R 15HD RSA D	RS-232 via 3 poles of a 3.5 mm captive screw connector, 5 pole
All other receivers	RS-232 via a 3.5 mm, 3 pole captive screw connector
Baud rates
MTP R 15HD RSA D, MTP 1500RL 15HD RS, MTP 1500RL 15HD RS SEQ	Up to 38400 bps at up to 1000' (304.8 m)
All other models	Up to 38400 bps at up to 600' (183 m)
NOTE     Higher data rates and distances are possible. Performance varies based on baud rate and cable length.
Protocol	Data bits = 5 - 8 Stop bits = 1 or 2 Parity = odd, even, none Flow control = XON, XOFF, none
NOTE     Protocol is mirrored between the transmitter and the receiver.
Serial control pin configuration	Captive screw connectors: 1 = TX, 2 = RX, 3 = GND
General
Recommended cable type
Models other than C7 models	CAT 5/5e/6 (shielded or unshielded)
Required cable type
MTP C7 15HD models	Extron DTP26 or CAT 7
Power	MTP 4T 15HD RS only: 100 VAC to 240 VAC, 50-60 Hz, 20 watts, internal
External power supply	All models except MTP 4T 15HD RS: 100 VAC to 240 VAC, 50-60 Hz, external; to 12 VDC, 1 A, regulated
Power input requirements	For models except MTP 4T 15HD RS.
MTP 1500RL 15HD models	12 VDC, 1.0 A max.
All other models	12 VDC, 0.5 A
Temperature/humidity	Storage: -40 to +158 °F (-40 to +70 °C) / 10% to 90%, noncondensing Operating: +32 to +122 °F (0 to +50 °C) / 10% to 90%, noncondensing
Cooling
MTP 1500RL 15HD models	Convection, vents sides to top
All other models	Convection, no vents
Mounting
Rack mount
MTP R 15HD RSA D	No
MTP 4T 15HD RS	Yes, with included mounting kit
All other models	Yes, with optional 1U rack shelf
Furniture mount
MTP R 15HD RSA D	Yes, using a standard electrical wall box or Decora® size mud ring
MTP 1500RL 15HD models	No
All other models except MTP 4T 15HD RS	Yes, with optional mini under-desk mounting kit
Wall mount
MTP 1500RL 15HD models	Yes, with optional wall mounting kit
Pole mount
MTP R 15HD RSA D	No
MTP 1500RL 15HD models	No
All other models except MTP 4T 15HD RS	Yes, with optional pole mounting kit
Enclosure type	Metal
Enclosure dimensions
MTP R 15HD RSA D
Faceplate	2.6" H* x 1.3" W x 0.24" D (6.6 cm H* x 3.3 cm W x 0.5 cm D) *Overall height is 4.1" (10.4 cm) including mounting tabs. (Fits the opening in a 1 gang, 4.4" H x 2.7" W Decora®-style wallplate. Depth excludes connectors.)
Device	2.75" H x 1.65" W x 1.3" D (7.0 cm H x 4.2 cm W x 3.3 cm D) (Depth excludes connectors.)
MTP 4T 15HD RS	1.7" H x 17.5" W x 8.5" D (1U high, full rack wide) (4.3 cm H x 44.4 cm W x 21.6 cm D) (Depth excludes connectors.)
MTP 1500RL 15HD models	1.0" H x 8.75" W x 6.0" D (half rack wide) (2.5 cm H x 22.2 cm W x 15.2 cm D) (Depth excludes connectors.)
All other models	1.7" H x 4.3" W x 3.0" D (1U high, quarter rack wide) (4.3 cm H x 10.9 cm W x 7.6 cm D) (Depth excludes connectors.)
Product weight
MTP 4T 15HD RS	6.0 lbs (2.7 kg)
MTP 1500RL 15HD models	1 lb (0.5 kg)
All other models	0.4 lbs (0.2 kg)
Shipping weight
MTP 4T 15HD RS	10 lbs (5 kg)
All other models	2 lbs (1 kg)
Vibration	ISTA 1A in carton (International Safe Transit Association)
Regulatory compliance
Safety	CE, c-UL, UL
EMI/EMC	CE, C-tick, FCC Class A, ICES, VCCI
Product warranty	3 years parts and labor
NOTE     All nominal levels are at ±10%.
NOTE     Specifications are subject to change without notice.
(7.6-111909-D10)

Versand-Abmessung und -Gewicht
Teilenummer	Höhe	Breite	Tiefe	Gewicht
60-1063-01	24,1 cm	18,1 cm	6,8 cm	0,76 kg
60-1063-02	24,1 cm	18,1 cm	6,8 cm	0,78 kg