MTP T 15HD A

Technische Daten

MTP 15HD A Series Combo
Video
Gain	Unity
Number/signal type	1 set of proprietary analog signals
Connectors
MTP R 15HD RSA D	1 female RJ-45 on a pigtail
All other models	1 female RJ-45
Video input and loop through — transmitters
Number/signal type
MTP T 15HD A, MTP C7 T 15HD A	1 analog RGBHV, RGBS, RGsB, RsGsBs, component video, S-video, or composite video 1 buffered RGBHV, RGBS, RGsB, RsGsBs local monitor loop through (includes ID bits)
MTP T 15HD A AAP, MTP T 15HD A D, MTP T 15HD A WM	1 analog RGBHV, RGBS, RGsB, RsGsBs, component video, S-video, or composite video
Connectors
MTP T 15HD A, MTP C7 T 15HD A	2 female 15-pin HD
All other transmitters	1 female 15-pin HD
Nominal level	1 Vp-p for Y of component video and S-video, and for composite video 0.7 Vp-p for RGB and for R-Y and B-Y of component video 0.3 Vp-p for C of S-video
Minimum/maximum levels	0.3 V to 1.45 Vp-p
Impedance	75 ohms
Horizontal frequency	15 kHz to 130 kHz
Vertical frequency	30 Hz to 150 Hz
Return loss	<-30 dB @ 5 MHz
DC offset (max. allowable)	250 mV
Video output — receivers (MTP RL 15HD A, MTP RL 15HD A SEQ, MTP R 15HD RSA D, MTP 1500RL 15HD A SEQ. MTP C7 RL 15HD A)
Number/signal type
MTP R 15HD RSA D	1 analog VGA-UXGA RGBHV, RGBS, RGsB, RsGsBs, HD component video, component video, S-video, or composite video
All other receivers	1 set of proprietary analog signals 1 analog RGBHV, RGBS, RGsB, RsGsBs, component video (bi-/tri-level sync), S-video, or composite video
Connectors
MTP R 15HD RSA D	1 female 15-pin HD
All other receivers	1 female RJ-45 1 female 15-pin HD
Nominal level	1 Vp-p for Y of component video and S-video, and for composite video 0.7 Vp-p for RGB and for R-Y and B-Y of component video 0.3 Vp-p for C of S-video
Minimum/maximum levels	0.3 V to 1.45 Vp-p
Impedance	75 ohms
Return loss	<-30 dB @ 5 MHz
DC offset
MTP R 15HD RSA D	<±20 mV with input at 0 offset
All other receivers	<±35 mV with input at 0 offset
Skew compensation	62 ns
Maximum resolution
MTP 1500RL 15HD A SEQ	Up to 1600x1200 and 1080p at 1500' Up to 1920x1200 and 2048x1080 at 1200'
All other models	Up to 1920x1200 or 2048x1080 or 1080p at 300' Up to 1024x768 at 600'
NOTE     See the user guide for the maximum distances recommended for specific resolutions.
Sync
Input type (transmitters)	RGBHV, RGBS, RGsB, RsGsBs
Output type (receivers)	RGBHV, RGBS, RGsB, RsGsBs
Standards	NTSC 3.58, NTSC 4.43, PAL, SECAM
Input level (transmitter)	3.5 V to 5.5 Vp-p, unterminated
Output level (receivers)	4.0 V to 5.0 Vp-p, unterminated
Input impedance (transmitter)	573 ohms ±5%
Output impedance (receivers)
MTP C7 15HD models	92 ohms ±8% (25 mA)
All other models	110 ohms
Polarity
Transmitter	Positive or negative (follows input polarity)
Receivers	Positive or negative (switch-selectable)
Audio — all models
Number/signal type	1 set of proprietary analog signals
Connectors	1 female RJ-45
Gain	Unbalanced output: 0 dB; balanced output: +6 dB
Frequency response	20 Hz to 20 kHz, ±1 dB
THD + Noise	0.15% @ 1 kHz, 0.3% @ 20 kHz at nominal level
S/N	>70 dB at maximum output (unweighted)
Stereo channel separation	>60 dB @ 1 kHz
CMRR	>43 dB @ 20 Hz to 20 kHz
Audio input — transmitters
Number/signal type	1 stereo, unbalanced
Connectors	(1) 3.5 mm mini stereo jack
Impedance	>10k ohms, unbalanced
Nominal level	+4 dBu (1.23 Vrms), -10 dBV (316 mVrms)
Maximum level
MTP C7 15HD models	+12 dBu, (unbalanced) at 1%THD+N
All other models	+18 dBu, (unbalanced) at 1%THD+N
NOTE     0 dBu = 0.775 Vrms, 0 dBV = 1 Vrms, 0 dBV ? 2 dBu
Audio output — MTP T 15HD A AAP, MTP T 15HD A D, MTP T 15HD A WM local stereo output
Number/signal type	1 stereo, balanced/unbalanced
Connectors	(1) 3.5 mm direct insertion captive screw connector, 5 pole
Impedance	50 ohms unbalanced, 100 ohms balanced
Gain error	±1 dB channel to channel
Maximum level (Hi-Z)	>+23 dBu, balanced or unbalanced at 1% THD+N
Maximum level (600 ohm)	>+17 dBm, balanced or unbalanced at 1% THD+N
Audio output — receivers
Number/signal type
MTP R 15HD RSA D	1 mono, balanced/unbalanced
All other receivers	2 mono, balanced/unbalanced
Connectors
MTP R 15HD RSA D	(1) 3.5 mm captive screw connector, 5 pole (uses 3 poles)
All other receivers	(1) 3.5 mm captive screw connector, 5 pole
Impedance	50 ohms unbalanced, 100 ohms balanced
Gain error	±1 dB channel to channel
Nominal level	+4 dBu (1.23 Vrms), -10 dBV (316 mVrms)
Maximum level
MTP R 15HD RSA D	14 dBm, unbalanced at 1% THD+N
All other receivers	+18 dBu, unbalanced at 1% THD+N
Control/remote — external device (pass-through, unidirectional or bidirectional) — MTP R 15HD RSA D only
Serial control port input/output	1 set of proprietary signals on a female RJ-45 jack
Serial control port output/input	RS-232 via 3 poles of a 3.5 mm captive screw connector, 5 pole
Baud rates	Up to 38400 bps at up to 600' (182.9 m)  (Higher data rates and distances are possible.  Performance varies based on baud rate and cable length.)
Protocol	Data bits = 5 - 8 Stop bits = 1 or 2 Parity = odd, even, none Flow control = XON, XOFF, none
NOTE     Protocol is mirrored between the transmitter and the receiver.
Serial control pin configuration	Captive screw connector: 1 = Tx, 2 = Rx, 3 = GND
General
Recommended cable type
Models other than C7 models	CAT 5/5e/6 (shielded or unshielded)
Required cable type
MTP C7 15HD models	Extron STP201 or CAT 7
Power supply	External Input: 100-240 VAC, 50-60 Hz Output: 12 VDC, 1 A, 12 watts
Power input requirements
MTP 1500RL 15HD A SEQ	12 VDC, 1 A
All other models	12 VDC, 0.5 A
Temperature/humidity	Storage: -40 to +158 °F (-40 to +70 °C) / 10% to 90%, noncondensing Operating: +32 to +122 °F (0 to +50 °C) / 10% to 90%, noncondensing
Cooling
MTP 1500RL 15HD A SEQ	Convection, vents sides to top
All other models	Convection, no vents
Mounting
Rack mount
MTP T 15HD A, MTP RL 15HD A, MTP RL 15HD A SEQ, MTP 1500RL 15HD A SEQ	Yes, with optional 1U rack shelf
Furniture or wall mount
MTP T 15HD A, MTP RL 15HD A, MTP RL 15HD A SEQ	Yes, with optional under-desk mounting kit
MTP T 15HD A AAP	Yes, with optional AAP mounting faceplates that have double space high AAP opening
MTP T 15HD A D, MTP R 15HD RSA D	Yes, in a decorator-style opening with a standard electrical wall box or decorator-style size mud ring
MTP T 15HD A WM	Yes, in a 1-gang opening
Wall mount
MTP 1500RL 15HD models	Yes, with optional wall mounting kit
Pole mount
MTP T 15HD A, MTP RL 15HD A, MTP RL 15HD A SEQ	Yes, with optional pole mounting kit
Enclosure type	Metal
Enclosure dimensions
MTP T 15HD A, MTP RL 15HD A, MTP RL 15HD A SEQ	1.7" H x 4.3" W x 3.0" D (1U high, quarter rack wide) 4.3 cm H x 10.9 cm W x 7.6 cm D (Depth excludes connectors.)
MTP C7 15HD models	1.7" H x 4.3" W x 3.0" D (1U high, quarter rack wide) (4.3 cm H x 10.9 cm W x 7.6 cm D) (Depth excludes connectors and knobs.)
MTP 1500RL 15HD SEQ models	1.0" H x 8.75" W x 6.0" D (half rack wide) (2.5 cm H x 22.2 cm W x 15.2 cm D) (Depth excludes connectors.)
Faceplates
MTP T 15HD A AAP	1.4" H x 3.5" W x 0.1" D (3.6 cm H x 8.9 cm W x 0.3 cm D) (double space high AAP plate)
MTP T 15HD A D, MTP R 15HD RSA D	2.6" H* x 1.3" W x 0.1" D (6.6 cm H* x 3.3 cm W x 0.3 cm D) (Fits the opening in a 1 gang, 4.4" H x 2.7" W decorator-style wallplate. Depth excludes connectors.) *Overall height is 4.1" (10.4 cm) including mounting tabs.
MTP T 15HD A WM	4.5" H x 2.8" W x 0.1" D (11.4 cm H x 7.1 cm W x 0.3 cm D) (1 gang)
Device
MTP R 15HD RSA D	2.75" H x 1.65" W x 1.3" D (7.0 cm H x 4.2 cm W x 3.3 cm D) (Depth excludes connectors.)
Other AAP, D, and WM models	2.7" H x 1.4" W x 1.4" D (6.9 cm H x 3.6 cm W x 3.6 cm D) (Depth excludes connectors.)
Product weight
MTP 1500RL 15HD A SEQ	1 lb (0.5 kg)
All other models	0.4 lbs (0.2 kg)
Vibration	ISTA 1A in carton (International Safe Transit Association)
Regulatory compliance
Safety	CE, c-UL, UL
EMI/EMC	CE, C-tick, FCC Class A, ICES, VCCI
Product warranty	3 years parts and labor
Everlast power supply warranty	7 years parts and labor
NOTE     All nominal levels are at ±10%.
NOTE     Specifications are subject to change without notice.
(CMS-041917-D18)

Versand-Abmessung und -Gewicht
Teilenummer	Höhe	Breite	Tiefe	Gewicht
60-1282-01	7,3 cm	18,6 cm	26,5 cm	0,83 kg