DTP CrossPoint 84

Technische Daten

DTP CrossPoint 84 Series
specification
Frame rate 1	24, 25, 30, 50, or 60 fps
Chroma sampling 1	4:4:4, 4:2:2, or 4:2:0
Color bit depth 1	8 bits per color
Signal type	HDMI 1.4, HDCP 1.4
Max. video data rate	10.2 Gbps (3.4 Gbps per color)
NOTE     1Subject to the maximum data rate limit. Use our calculator (http://www.extron.com/product/videotools.aspx) to determine video parameters supported by this data rate.
Video
Routing	8 x 4 matrix
Maximum data rate	10.2 Gbps (3.4 Gbps per color)
Maximum pixel clock	300 MHz (600 MHz for 4K rates with 4:2:0 chroma subsampling)
Resolution	Up to 2560x1600* @ 60 Hz or 4K (4096x2160) @ 30 Hz, UHD (3840x2160) @ 30 Hz 4K/UHD @ 60 Hz with 4:2:0 chroma subsampling (* reduced blanking)
Formats	RGB and YCbCr digital video
Standards	DVI 1.0, HDMI, HDCP 1.3, CEA-861E
Video input
Number/signal type	6 HDMI digital video (HDCP compliant) 2 DTP or XTP (configurable)
Connectors	6 female HDMI type A 2 female RJ-45
Matrix video outputs (non scaled)
Number/signal type	2 HDMI digital video (HDCP compliant)
Connectors	2 female HDMI
Scaled TP outputs
Number/signal type	2 DTP, XTP, or HDBaseT (configurable)
Connectors	2 female RJ-45
Video processing
Digital pixel data bit depth	8, 10, or 12 bits per channel; 165 MHz pixel clock (HDMI)
Colors	1.07 billion (10-bit processing)
Video input
Horizontal frequency	15 kHz to 100 kHz
Vertical frequency	24 Hz to 75 Hz
Resolution range	640x480 to 1600x1200 and 1920x1200* 480i, 480p, 576i, 576p, 720p, 1080i, 1080p, and 2K *reduced blanking
Scaled resolutions	640x4808, 800x6008, 852x4808, 1024x7688, 1024x8528, 1024x10248,1280x7688, 1280x8008, 1280x10248, 1360x7658, 1360x7688, 1365x7688, 1366x7688, 1365x10248, 1400x10508, 1440x9008, 1600x9008, 1600x12008, 1680x10508, 1920x12008 HDTV 480p7,8, 576p6, 720p3,4,5,6,7,8, 1080i6,7,8, 1080p1,2,3,4,5,6,7,8, 2048x10801,2,3,4,5,6,7,8 1 = at 23.98 Hz, 2 = at 24 Hz, 3 = at 25 Hz,4 = at 29.97 Hz, 5 = at 30 Hz, 6 = at 50 Hz, 7 = at 59.94 Hz, 8 = at 60 Hz
Shielded twisted pair interconnection
Connectors	Female RJ-45
Termination standard	TIA/EIA T568B
Signal transmission distance
Resolutions up to 1920x1200 and 1080p
DTP 330	Up to 330' (100 m) using shielded twisted pair cable or XTP DTP 24 TP cable
DTP 230	Up to 230' (70 m) using shielded twisted pair cable or XTP DTP 24 TP cable
2560x1600* and 4k @ 30 Hz (* reduced blanking)
DTP 330	Up to 330' (100 m) using shielded twisted pair cable or XTP DTP 24 TP cable
DTP 230	Up to 130' (40 m) using shielded twisted pair cable or XTP DTP 24 TP cable
Cable requirements	Solid conductor, 24 AWG or better
Cable recommendations	400 MHz bandwidth, STP (shielded twisted pair)
NOTE     Extron XTP DTP 24 shielded twisted pair cable is strongly recommended for optimal performance.
NOTE     Input and output mode signaling: DTP:        HDMI with embedded audio, analog audio, RS-232 and IR, and remote power XTP:        HDMI with embedded audio plus RS-232 and IR HDBT:    HDMI with embedded audio plus RS-232 and IR
Audio system (mic/line input to line output)
Gain	Unbalanced output: -6 dB; balanced output: 0 dB
Frequency response	20 Hz to 20 kHz, ±0.2 dB
Input impedance	>10k ohms unbalanced, >20k ohms balanced
THD + Noise	0.01% at 1 kHz nominal level
S/N	105 dB at maximum balanced output (unweighted)
Crosstalk	<-90 dB @ 20 Hz to 20 kHz, fully loaded
Stereo channel separation	>80 dB @ 20 Hz to 20 kHz
Digital conversion	24-bit, 48 kHz
Audio
Routing	8 x 4 stereo switching matrix 4 x 4 microphone mixing matrix
Supported formats — Pass through
HDMI connectors	LPCM up to 7.1/24-bit/192kHz, Dolby TrueHD, Dolby Digital Plus, Dolby Digital EX, Dolby Digital 5.1, Dolby Digital 2/0 Surround, Dolby Digital 2/0, DTS-HD Master Audio, DTS-HD, DTS ES Discrete 6.1, DTS ES Matrix 6.1, DTS Digital Surround 5.1, DTS 2 Channel
Analog conectors	Analog stereo audio
DTP connectors	De-embedded from HDMI [PCM only] or remote balanced/unbalanced analog
Audio input
Number/signal type	6 stereo, analog line level, balanced or unbalanced 6 stereo, de-embedded from HDMI (PCM only) 2 DTP (de-embedded from HDMI [PCM only] and remote balanced/unbalanced analog), or XTP (embedded digital)
Connectors	(6) 3.5 mm captive screw connectors, 5-pole for analog line level inputs 6 female HDMI type A 2 female RJ-45
Analog audio
Nominal level	+4 dBu, -10 dBV adjustable via input gain
Maximum level	+21 dBu balanced, +15 dBu unbalanced
Input gain adjustment	-18 dB to +24 dB, 0.1 dB steps, adjustable per input
NOTE     Unbalanced analog inputs at a DTP Tx input have +12 dB of gain applied to bring the signal to a nominal level for balanced operation.
NOTE     0 dBu = 0.775 Vrms, 0 dBV = 1 Vrms, 0 dBV ? 2 dBu
Mic/line input
Number/signal type	4 mono, mic/line, balanced/unbalanced (with phantom power)
Connectors	(4) 3.5 mm captive screw connectors, 3-pole
Impedance	10k ohms unbalanced, 20k ohms balanced
Nominal level	-60 dBV, +4 dBu, -10 dBV, adjustable via input gain
Maximum level	>+21 dBu at rated THD+N when mic gain is set to 0 dB
Equivalent input noise	<-120 dBV (1.0 µVrms) at +40 dB input gain
CMRR	>70 dB typical
Input gain adjustment	-18 dB to +80 dB, in 0.1 dB steps, adjustable per input
Microphone volume range	-100 dB to +12 dB
DC phantom power	+48 VDC, ±10% (inputs 1-4) switched on or off
Audio output
Number/signal type	4 HDMI embedded 2 DTP (embedded digital and remote balanced/unbalanced analog), XTP (embedded digital), or HDBaseT (embedded digital) 4 stereo balanced/unbalanced analog (variable)
Connectors	4 female HDMI 2 RJ-45 (4) 3.5 mm captive screw, 5-pole
Impedance
Stereo audio	50 ohms unbalanced, 100 ohms balanced
S/PDIF	75 ohms
Gain error	±0.1 dB channel to channel
Maximum level (Hi-Z)	>+21 dBu, balanced or +15 dBu unbalanced
Output volume range	0 to -100 dB in 0.1 dB steps
EXP port
Transmission type	Proprietary
Connectors	1 RJ-45
Inputs	8 channels Rx
Outputs	16 channels Tx
Audio format	24 bit, 48 kHz sampling, uncompressed
EXP cable	Shielded CAT 6 up to 10 meters
Audio output — power amplifier (DTP CrossPoint 84 IPCP SA and DTP CrossPoint 84 IPCP MA models)
Number/signal type
SA models	1 stereo or mono (2 channels total)
MA models	1 mono, 70 V
Connector
NOTE     This connector accepts wires of 22 AWG to 12 AWG.
SA models	(1) 5 mm screw lock captive screw connector, 4-pole
MA models	(1) 5 mm screw lock captive screw connector, 2-pole
Load impedance
SA models	4 ohms minimum
MA models	50 ohms minimum
High pass filter (MA models)	80 Hz, 12 dB/octave roll off
Amplifier type	Class D
Output power
SA models	25 watts (rms) per channel, 8 ohms, 1 kHz, 0.1% THD 50 watts per channel, 4 ohms, 1 kHz, 0.1% THD
MA models	100 watts (rms) @ 70 V, 1 kHz, 0.1% THD
Protection	Clip limiting, thermal, short circuit, DC output
Frequency response
SA models	20 Hz to 20 kHz, +1/?3 dB @ 1 watt
MA models	80 Hz to 20 kHz, +1/?3 dB @ 1 watt
THD + Noise	<0.1%, 1 kHz, 3 dB below clipping
S/N	>90 dB, 20 Hz to 20 kHz, unweighted
Control/remote — switcher
Serial control port	1 bidirectional RS-232, 3.5 mm captive screw connector, 3-pole (rear panel)
Baud rate and protocol	9600 (default) to 115200 baud, 8 data bits, 1 stop bit, no parity (default)
Serial control pin configuration	1 = Tx, 2 = Rx, 3 = Gnd
USB control port	1 front panel female USB mini-B
USB standards	USB 2.0, low speed
Ethernet control port	1 female RJ-45 connector
Ethernet data rate	10/100Base-T, half/full duplex with autodetect
Ethernet protocol	DHCP, DNS, HTTP, HTTPS, ICMP, NTP, SFTP, SMTP, SNMP, SSH, TCP/IP, UDP/IP, ARP, Telnet
Ethernet default settings	Link speed and duplex level = autodetected IP address = 192.168.254.254 Subnet mask = 255.255.0.0 Default gateway = 0.0.0.0 DHCP = off
Web server	Up to 200 simultaneous sessions 40.0 MB nonvolatile user memory
Program control	Extron control/configuration program for Windows® Extron Simple Instruction Set (SIS™) Microsoft® Internet Explorer®, Telnet
Control/remote — external device (pass-through, unidirectional or bidirectional) (RS-232/IR over TP)
NOTE     Protocol is mirrored between the connected TP endpoints and the "Over TP" ports on the DTP CrossPoint 84. Signals from a control device pass into each DTP CrossPoint 84 "Over TP" port, are embedded with the TP signal, and sent to individual TP Tx or Rx endpoints for control of remote sink or source devices. The "Over TP" ports are simply pass-through connections to TP endpoints. There is no IR insertion from any DTP CrossPoint 84 control port to the “Over TP” ports. RS-232 can be inserted from the Ethernet connection.
Serial control pass-through ports
DTP CrossPoint 84 input/TP Tx	RS-232 via (2) 3.5 mm, 5-pole captive screw connectors (shared with IR ports)
DTP CrossPoint 84 output/TP Rx	RS-232 via (2) 3.5 mm, 5-pole captive screw connectors (shared with IR ports)
Baud rates	300 to 115200 baud
Protocol	8 or 7 data bits 1 or 2 stop bits no parity (default), even or odd parity
Serial control pin configuration	1 = Tx, 2 = Rx, 3 = Gnd
IR pass-through control ports	TTL level (0 to 5 V) modulated infrared control from 30 kHz up to 60 kHz
DTP CrossPoint 84 input/TP Tx	(2) 3.5 mm captive screw connectors, 5-pole (shared with RS-232 ports)
DTP CrossPoint 84 output/TP Rx	(2) 3.5 mm captive screw connectors, 5-pole (shared with RS-232 ports)
IR control pin configuration	3 = Gnd, 4 = IR Tx, 5 = IR Rx
Control/remote — IPCP Pro 350 control processor (DTP CrossPoint 84 IPCP models)
Memory
SDRAM	512 MB
Flash	4.5 GB
Software and control options
Software	Extron Global Configurator Plus and Professional for Windows®
Control options	GlobalViewer®, TouchLink® for Web, TouchLink for iPad®, or TouchLink Pro touchpanels
Ethernet control
Network interface controllers (NICs)	1
Network switch	1 unmanaged 3 port switch
Connectors	3 female RJ-45 connectors
Data rate	10/100/1000Base-T, half/full duplex with autodetect
Protocols	DHCP, DNS, HTTP, HTTPS, ICMP, NTP, SFTP, SMTP, SNMP, SSH, TCP/IP, UDP/IP
Default settings	Link speed and duplex level = autodetected IP address = 192.168.254.250 Subnet mask = 255.255.255.0 Gateway = 0.0.0.0 DHCP = off DNS: 127.0.0.1
Serial control
Quantity/type	1 bidirectional RS-232, RS-422, RS-485 (port 1) 2 bidirectional RS-232 (ports 2 and 3)
Connectors	(1) 3.5 mm captive screw connector, 5-pole (2) 3.5 mm captive screw connectors, 3-pole
Baud rate and protocol	300 to 115200 baud (9600 baud = default); 8 (default) or 7 data bits; 1 (default) or 2 stop bits; no parity (default), even, odd, mark, or space parity
NOTE     The 5-pole ports support both hardware and software flow control. The 3-pole ports support software flow control. The default for both types of ports is no flow control.
Pin configurations, serial, 5-pole captive screw
RS-232 (default)	Pin 1 = Tx, 2 = Rx, 3 = Gnd, 4 = RTS, 5 = CTS
RS-422	Pin 1 = Tx-, 2 = Rx-, 3 = Gnd, 4 = Tx+, 5 = Rx+
RS-485	Pins 1 and 2 (tied together) = data-, 3 = Gnd, 4 and 5 (tied together) = data+
Pin configurations, serial, 3-pole captive screw	Pin 1 = Tx, 2 = Rx, 3 = Gnd
Digital I/O control
Quantity/type	4 digital input/output (configurable)
Connectors	(1) 3.5 mm captive screw connector, 5-pole
Digital inputs
Input voltage range	0 to 24 VDC, clamped at +30 VDC
Input impedance	29k ohms
Programmable pullup	1k ohms to +5 VDC
Threshold low to high	>2.8 VDC
Threshold high to low	<2.0 VDC
Digital outputs	250 mA sink from 24 VDC max.
Pin configurations	1, 2, 3, 4 = digital I/Os 1, 2, 3, 4; 5 = Gnd
IR/serial control
Quantity/type	2 programmable: unidirectional RS-232 (±5 V), or TTL level (0 to 5 V) infrared (carrier and non-carrier) up to 300 kHz
Connector	(1) 3.5 mm captive screw connector, 5-pole
Baud rate and protocol (RS-232)	300 to 115200 baud (9600 baud = default); 8 (default) or 7 data bits; 1 (default) or 2 stop bits; no parity (default), even, odd, mark, or space parity
Pin configurations	For each port, pin 1 = signal, 2 = Gnd
IR output carrier frequency	30 kHz to 300 kHz
Relay control
Quantity/type	4 normally open relays
Relay control connectors	(1) 3.5 mm captive screw connector, 6-pole
Relay control contact rating	24 VDC, 1 A
General
Power supply	Internal Input: 100-240 VAC, 50-60 Hz
Power consumption	111 watts
Remote power capability	Supports up to four endpoints (two DTP Tx, two DTP Rx) (remote power not available in XTP and HDBaseT modes)
Temperature/humidity	Storage: -40 to +158 °F (-40 to +70 °C) / 10% to 90%, noncondensing Operating: +32 to +122 °F (0 to +50 °C) / 10% to 90%, noncondensing
Cooling	Fans, air flows from left to right (as viewed from front panel)
Thermal dissipation	265 BTU/hr
Mounting
Rack mount	Yes
Enclosure type	Metal
Enclosure dimensions	3.5" H x 17.4" W x 15.3" D (2U high, full rack wide) (8.9 cm H x 43.2 cm W x 38.9 cm D) (Depth excludes connectors and knobs. Width excludes rack ears.)
Product weight	11.4 lbs (5.2 kg)
Shipping weight	14 lbs (6.0 kg)
DIM weight	22 lbs (10 kg)
Vibration	ISTA 1A in carton (International Safe Transit Association)
Regulatory compliance
Safety	CE, c-UL, UL
EMI/EMC	CE, C-tick, FCC Class A, ICES, VCCI
Environmental	Complies with the appropriate requirements of RoHS, WEEE.
Product warranty	3 years parts and labor
Everlast power supply warranty	7 years parts and labor
NOTE     Specifications are subject to change without notice.
NOTE     All nominal levels are at ±10%.
(120216-D9)

Versand-Abmessung und -Gewicht
Teilenummer	Höhe	Breite	Tiefe	Gewicht
60-1368-01	19,1 cm	57,2 cm	54,6 cm	5,44 kg
60-1368-12	19,1 cm	57,2 cm	54,6 cm	5,98 kg
60-1368-12A	19,1 cm	57,2 cm	54,6 cm	5,98 kg
60-1368-13	19,1 cm	57,2 cm	54,6 cm	5,98 kg
60-1368-13A	19,1 cm	57,2 cm	54,6 cm	5,98 kg