DTP CrossPoint 84

Preis auf Anfrage

  • inkl. 20 % USt zzgl. Versandkosten
    zurzeit nicht lagernd:
    Lieferzeit 5-7 Tage*

    *Alle Lieferzeiten sind ungefähre Angaben und können von der tatsächlichen Lieferzeit abweichen!

Hersteller
Extron
Art.Nr.
60-1368-13A
EAN
60-1368-13A
Gewicht
8 kg

Produktbeschreibung

Hauptmerkmale

  • 8x4 Kreuzschiene für 4K, Skalierer, Audio-DSP-Prozessor, Audioverstärker und Steuerungsprozessor in einem Gerät
  • Zwei DTP- und sechs HDMI-Eingänge
  • Zwei HDMI- und zwei unabhängig skalierte DTP-Ausgänge
  • Integrierte DTP-Eingänge und -Ausgänge unterstützen die Übertragung von Video, Steuerung und Audio bis zu 100 m über ein geschirmtes CATx-Kabel
  • Unterstützt 4K-Signale an allen Eingängen und beiden HDMI-Ausgängen
  • Verfügbar mit integriertem IPCP Pro 350-Steuerungsprozessor
Modell Beschreibung der Version Teilenummer
DTP CrossPoint 84 Vorverstärker-Ausgang ohne Verstärker und Steuerungsprozessor 60-1368-01
DTP CrossPoint 84 IPCP SA Stereo-Verstärker mit 2 x 50 W 60-1368-12
DTP CrossPoint 84 IPCP SA Stereo-Verstärker mit 2 x 50 W, LinkLicense-Upgrade für Benutzeroberflächen 60-1368-12A
DTP CrossPoint 84 IPCP MA 70 Mono-Verstärker mit 100 W bei 70 V 60-1368-13
DTP CrossPoint 84 IPCP MA 70 Mono-Verstärker mit 100 W bei 70 V, LinkLicense-Upgrade für Benutzeroberflächen 60-1368-13A

Technische Daten

Technische Daten

DTP CrossPoint 84 Series
specification
   
    Frame rate 1  24, 25, 30, 50, or 60 fps
    Chroma sampling 1  4:4:4, 4:2:2, or 4:2:0
    Color bit depth 1  8 bits per color
    Signal type  HDMI 1.4, HDCP 1.4
    Max. video data rate  10.2 Gbps (3.4 Gbps per color)
    NOTE     1Subject to the maximum data rate limit. Use our calculator (http://www.extron.com/product/videotools.aspx) to determine video parameters supported by this data rate.
Video
    Routing  8 x 4 matrix
    Maximum data rate  10.2 Gbps (3.4 Gbps per color)
    Maximum pixel clock  300 MHz (600 MHz for 4K rates with 4:2:0 chroma subsampling)
    Resolution  Up to 2560x1600* @ 60 Hz or
4K (4096x2160) @ 30 Hz, UHD (3840x2160) @ 30 Hz
4K/UHD @ 60 Hz with 4:2:0 chroma subsampling
(* reduced blanking)
    Formats  RGB and YCbCr digital video
    Standards  DVI 1.0, HDMI, HDCP 1.3, CEA-861E
Video input
    Number/signal type  6 HDMI digital video (HDCP compliant)
2 DTP or XTP (configurable)
    Connectors  6 female HDMI type A
2 female RJ-45
Matrix video outputs (non scaled)
    Number/signal type  2 HDMI digital video (HDCP compliant)
    Connectors  2 female HDMI
Scaled TP outputs
    Number/signal type  2 DTP, XTP, or HDBaseT (configurable)
    Connectors  2 female RJ-45
    Video processing 
       Digital pixel data bit depth  8, 10, or 12 bits per channel; 165 MHz pixel clock (HDMI)
       Colors  1.07 billion (10-bit processing)
    Video input 
       Horizontal frequency  15 kHz to 100 kHz
       Vertical frequency  24 Hz to 75 Hz
       Resolution range  640x480 to 1600x1200 and 1920x1200* 480i, 480p, 576i, 576p, 720p, 1080i, 1080p, and 2K
*reduced blanking
    Scaled resolutions  640x4808, 800x6008, 852x4808, 1024x7688, 1024x8528, 1024x10248,1280x7688, 1280x8008, 1280x10248, 1360x7658, 1360x7688, 1365x7688, 1366x7688, 1365x10248, 1400x10508, 1440x9008, 1600x9008, 1600x12008, 1680x10508, 1920x12008

HDTV 480p7,8, 576p6, 720p3,4,5,6,7,8, 1080i6,7,8, 1080p1,2,3,4,5,6,7,8, 2048x10801,2,3,4,5,6,7,8
1 = at 23.98 Hz, 2 = at 24 Hz, 3 = at 25 Hz,4 = at 29.97 Hz, 5 = at 30 Hz, 6 = at 50 Hz, 7 = at 59.94 Hz, 8 = at 60 Hz

Shielded twisted pair interconnection
    Connectors  Female RJ-45
    Termination standard  TIA/EIA T568B
    Signal transmission distance 
       Resolutions up to 1920x1200 and 1080p 
          DTP 330  Up to 330' (100 m) using shielded twisted pair cable or XTP DTP 24 TP cable
          DTP 230  Up to 230' (70 m) using shielded twisted pair cable or XTP DTP 24 TP cable
       2560x1600* and 4k @ 30 Hz (* reduced blanking) 
          DTP 330  Up to 330' (100 m) using shielded twisted pair cable or XTP DTP 24 TP cable
          DTP 230  Up to 130' (40 m) using shielded twisted pair cable or XTP DTP 24 TP cable
    Cable requirements  Solid conductor, 24 AWG or better
    Cable recommendations  400 MHz bandwidth, STP (shielded twisted pair)
    NOTE     Extron XTP DTP 24 shielded twisted pair cable is strongly recommended for optimal performance.
    NOTE     Input and output mode signaling:
DTP:        HDMI with embedded audio, analog audio, RS-232 and IR, and remote power
XTP:        HDMI with embedded audio plus RS-232 and IR
HDBT:    HDMI with embedded audio plus RS-232 and IR
Audio system (mic/line input to line output)
    Gain  Unbalanced output: -6 dB; balanced output: 0 dB
    Frequency response  20 Hz to 20 kHz, ±0.2 dB
    Input impedance  >10k ohms unbalanced, >20k ohms balanced
    THD + Noise  0.01% at 1 kHz nominal level
    S/N  105 dB at maximum balanced output (unweighted)
    Crosstalk  <-90 dB @ 20 Hz to 20 kHz, fully loaded
    Stereo channel separation  >80 dB @ 20 Hz to 20 kHz
    Digital conversion  24-bit, 48 kHz
Audio
    Routing  8 x 4 stereo switching matrix
4 x 4 microphone mixing matrix
    Supported formats — Pass through  
       HDMI connectors  LPCM up to 7.1/24-bit/192kHz, Dolby TrueHD, Dolby Digital Plus, Dolby Digital EX, Dolby Digital 5.1, Dolby Digital 2/0 Surround, Dolby Digital 2/0, DTS-HD Master Audio, DTS-HD, DTS ES Discrete 6.1, DTS ES Matrix 6.1, DTS Digital Surround 5.1, DTS 2 Channel
       Analog conectors  Analog stereo audio
       DTP connectors  De-embedded from HDMI [PCM only] or remote balanced/unbalanced analog
Audio input
    Number/signal type  6 stereo, analog line level, balanced or unbalanced
6 stereo, de-embedded from HDMI (PCM only)
2 DTP (de-embedded from HDMI [PCM only] and remote balanced/unbalanced analog), or XTP (embedded digital)
    Connectors  (6) 3.5 mm captive screw connectors, 5-pole for analog line level inputs
6 female HDMI type A
2 female RJ-45
    Analog audio 
       Nominal level  +4 dBu, -10 dBV adjustable via input gain
       Maximum level  +21 dBu balanced, +15 dBu unbalanced
       Input gain adjustment  -18 dB to +24 dB, 0.1 dB steps, adjustable per input
       NOTE     Unbalanced analog inputs at a DTP Tx input have +12 dB of gain applied to bring the signal to a nominal level for balanced operation.
       NOTE     0 dBu = 0.775 Vrms, 0 dBV = 1 Vrms, 0 dBV ? 2 dBu
Mic/line input
    Number/signal type  4 mono, mic/line, balanced/unbalanced (with phantom power)
    Connectors  (4) 3.5 mm captive screw connectors, 3-pole
    Impedance  10k ohms unbalanced, 20k ohms balanced
    Nominal level  -60 dBV, +4 dBu, -10 dBV, adjustable via input gain
    Maximum level  >+21 dBu at rated THD+N when mic gain is set to 0 dB
    Equivalent input noise  <-120 dBV (1.0 µVrms) at +40 dB input gain
    CMRR  >70 dB typical
    Input gain adjustment  -18 dB to +80 dB, in 0.1 dB steps, adjustable per input
    Microphone volume range  -100 dB to +12 dB
    DC phantom power  +48 VDC, ±10% (inputs 1-4) switched on or off
Audio output
    Number/signal type  4 HDMI embedded
2 DTP (embedded digital and remote balanced/unbalanced analog), XTP (embedded digital), or HDBaseT (embedded digital)
4 stereo balanced/unbalanced analog (variable)
    Connectors  4 female HDMI
2 RJ-45
(4) 3.5 mm captive screw, 5-pole
    Impedance 
       Stereo audio  50 ohms unbalanced, 100 ohms balanced
       S/PDIF  75 ohms
    Gain error  ±0.1 dB channel to channel
    Maximum level (Hi-Z)  >+21 dBu, balanced or +15 dBu unbalanced
    Output volume range  0 to -100 dB in 0.1 dB steps
EXP port
    Transmission type  Proprietary
    Connectors  1 RJ-45
    Inputs  8 channels Rx
    Outputs  16 channels Tx
    Audio format  24 bit, 48 kHz sampling, uncompressed
    EXP cable  Shielded CAT 6 up to 10 meters
Audio output — power amplifier (DTP CrossPoint 84 IPCP SA and DTP CrossPoint 84 IPCP MA models)
    Number/signal type 
       SA models  1 stereo or mono (2 channels total)
       MA models  1 mono, 70 V
    Connector 
    NOTE     This connector accepts wires of 22 AWG to 12 AWG.
       SA models  (1) 5 mm screw lock captive screw connector, 4-pole
       MA models  (1) 5 mm screw lock captive screw connector, 2-pole
    Load impedance 
       SA models  4 ohms minimum
       MA models  50 ohms minimum
    High pass filter (MA models)  80 Hz, 12 dB/octave roll off
    Amplifier type  Class D
    Output power 
       SA models  25 watts (rms) per channel, 8 ohms, 1 kHz, 0.1% THD
50 watts per channel, 4 ohms, 1 kHz, 0.1% THD
       MA models  100 watts (rms) @ 70 V, 1 kHz, 0.1% THD
    Protection  Clip limiting, thermal, short circuit, DC output
    Frequency response 
       SA models  20 Hz to 20 kHz, +1/?3 dB @ 1 watt
       MA models  80 Hz to 20 kHz, +1/?3 dB @ 1 watt
    THD + Noise  <0.1%, 1 kHz, 3 dB below clipping
    S/N  >90 dB, 20 Hz to 20 kHz, unweighted
Control/remote — switcher
    Serial control port  1 bidirectional RS-232, 3.5 mm captive screw connector, 3-pole (rear panel)
    Baud rate and protocol  9600 (default) to 115200 baud, 8 data bits, 1 stop bit, no parity (default)
    Serial control pin configuration  1 = Tx, 2 = Rx, 3 = Gnd
    USB control port  1 front panel female USB mini-B
    USB standards  USB 2.0, low speed
    Ethernet control port  1 female RJ-45 connector
    Ethernet data rate  10/100Base-T, half/full duplex with autodetect
    Ethernet protocol  DHCP, DNS, HTTP, HTTPS, ICMP, NTP, SFTP, SMTP, SNMP, SSH, TCP/IP, UDP/IP, ARP, Telnet
    Ethernet default settings  Link speed and duplex level = autodetected
IP address = 192.168.254.254
Subnet mask = 255.255.0.0
Default gateway = 0.0.0.0
DHCP = off
    Web server  Up to 200 simultaneous sessions
40.0 MB nonvolatile user memory
    Program control  Extron control/configuration program for Windows®
Extron Simple Instruction Set (SIS)
Microsoft® Internet Explorer®, Telnet
Control/remote — external device (pass-through, unidirectional or bidirectional) (RS-232/IR over TP)
    NOTE     Protocol is mirrored between the connected TP endpoints and the "Over TP" ports on the DTP CrossPoint 84. Signals from a control device pass into each DTP CrossPoint 84 "Over TP" port, are embedded with the TP signal, and sent to individual TP Tx or Rx endpoints for control of remote sink or source devices.
The "Over TP" ports are simply pass-through connections to TP endpoints. There is no IR insertion from any DTP CrossPoint 84 control port to the “Over TP” ports. RS-232 can be inserted from the Ethernet connection.
    Serial control pass-through ports 
       DTP CrossPoint 84 input/TP Tx  RS-232 via (2) 3.5 mm, 5-pole captive screw connectors (shared with IR ports)
       DTP CrossPoint 84 output/TP Rx  RS-232 via (2) 3.5 mm, 5-pole captive screw connectors (shared with IR ports)
    Baud rates  300 to 115200 baud
    Protocol  8 or 7 data bits
1 or 2 stop bits
no parity (default), even or odd parity
    Serial control pin configuration  1 = Tx, 2 = Rx, 3 = Gnd
    IR pass-through control ports  TTL level (0 to 5 V) modulated infrared control from 30 kHz up to 60 kHz
       DTP CrossPoint 84 input/TP Tx  (2) 3.5 mm captive screw connectors, 5-pole (shared with RS-232 ports)
       DTP CrossPoint 84 output/TP Rx  (2) 3.5 mm captive screw connectors, 5-pole (shared with RS-232 ports)
    IR control pin configuration  3 = Gnd, 4 = IR Tx, 5 = IR Rx
Control/remote — IPCP Pro 350 control processor (DTP CrossPoint 84 IPCP models)
    Memory 
       SDRAM  512 MB
       Flash  4.5 GB
    Software and control options 
       Software  Extron Global Configurator Plus and Professional for Windows®
       Control options  GlobalViewer®, TouchLink® for Web, TouchLink for iPad®, or TouchLink Pro touchpanels
    Ethernet control 
       Network interface controllers (NICs)  1
       Network switch  1 unmanaged 3 port switch
       Connectors  3 female RJ-45 connectors
       Data rate  10/100/1000Base-T, half/full duplex with autodetect
       Protocols  DHCP, DNS, HTTP, HTTPS, ICMP, NTP, SFTP, SMTP, SNMP, SSH, TCP/IP, UDP/IP
       Default settings  Link speed and duplex level = autodetected
IP address = 192.168.254.250
Subnet mask = 255.255.255.0
Gateway = 0.0.0.0
DHCP = off
DNS: 127.0.0.1
    Serial control 
       Quantity/type  1 bidirectional RS-232, RS-422, RS-485 (port 1)
2 bidirectional RS-232 (ports 2 and 3)
       Connectors  (1) 3.5 mm captive screw connector, 5-pole
(2) 3.5 mm captive screw connectors, 3-pole
       Baud rate and protocol  300 to 115200 baud (9600 baud = default); 8 (default) or 7 data bits; 1 (default) or 2 stop bits;
no parity (default), even, odd, mark, or space parity
       NOTE     The 5-pole ports support both hardware and software flow control.
The 3-pole ports support software flow control.
The default for both types of ports is no flow control.
      Pin configurations, serial, 5-pole captive screw
          RS-232 (default)  Pin 1 = Tx, 2 = Rx, 3 = Gnd, 4 = RTS, 5 = CTS
          RS-422  Pin 1 = Tx-, 2 = Rx-, 3 = Gnd, 4 = Tx+, 5 = Rx+
          RS-485  Pins 1 and 2 (tied together) = data-, 3 = Gnd, 4 and 5 (tied together) = data+
       Pin configurations, serial, 3-pole captive screw   Pin 1 = Tx, 2 = Rx, 3 = Gnd
    Digital I/O control 
       Quantity/type  4 digital input/output (configurable)
       Connectors  (1) 3.5 mm captive screw connector, 5-pole
       Digital inputs 
          Input voltage range  0 to 24 VDC, clamped at +30 VDC
          Input impedance  29k ohms
          Programmable pullup  1k ohms to +5 VDC
          Threshold low to high  >2.8 VDC
          Threshold high to low  <2.0 VDC
       Digital outputs  250 mA sink from 24 VDC max.
       Pin configurations  1, 2, 3, 4 = digital I/Os 1, 2, 3, 4; 5 = Gnd
    IR/serial control 
       Quantity/type  2 programmable: unidirectional RS-232 (±5 V), or TTL level (0 to 5 V) infrared (carrier and non-carrier) up to 300 kHz
       Connector  (1) 3.5 mm captive screw connector, 5-pole
       Baud rate and protocol (RS-232)  300 to 115200 baud (9600 baud = default); 8 (default) or 7 data bits; 1 (default) or 2 stop bits;
no parity (default), even, odd, mark, or space parity
       Pin configurations  For each port, pin 1 = signal, 2 = Gnd
       IR output carrier frequency  30 kHz to 300 kHz
    Relay control 
       Quantity/type  4 normally open relays
       Relay control connectors  (1) 3.5 mm captive screw connector, 6-pole
       Relay control contact rating  24 VDC, 1 A
General
    Power supply  Internal
Input: 100-240 VAC, 50-60 Hz
    Power consumption  111 watts
    Remote power capability  Supports up to four endpoints (two DTP Tx, two DTP Rx) (remote power not available in XTP and HDBaseT modes)
    Temperature/humidity  Storage: -40 to +158 °F (-40 to +70 °C) / 10% to 90%, noncondensing
Operating: +32 to +122 °F (0 to +50 °C) / 10% to 90%, noncondensing
    Cooling  Fans, air flows from left to right (as viewed from front panel)
    Thermal dissipation  265 BTU/hr
    Mounting 
       Rack mount  Yes
    Enclosure type  Metal
    Enclosure dimensions  3.5" H x 17.4" W x 15.3" D (2U high, full rack wide)
(8.9 cm H x 43.2 cm W x 38.9 cm D)
(Depth excludes connectors and knobs. Width excludes rack ears.)
    Product weight  11.4 lbs (5.2 kg)
    Shipping weight  14 lbs (6.0 kg)
    DIM weight  22 lbs (10 kg)
    Vibration  ISTA 1A in carton (International Safe Transit Association)
    Regulatory compliance 
       Safety  CE, c-UL, UL
       EMI/EMC  CE, C-tick, FCC Class A, ICES, VCCI
       Environmental  Complies with the appropriate requirements of RoHS, WEEE.
    Product warranty  3 years parts and labor
    Everlast power supply warranty  7 years parts and labor
    NOTE     Specifications are subject to change without notice.
    NOTE     All nominal levels are at ±10%.
(120216-D9)
Versand-Abmessung und -Gewicht
    Teilenummer Höhe Breite Tiefe Gewicht
    60-1368-01 19,1 cm 57,2 cm 54,6 cm 5,44 kg
    60-1368-12 19,1 cm 57,2 cm 54,6 cm 5,98 kg
    60-1368-12A 19,1 cm 57,2 cm 54,6 cm 5,98 kg
    60-1368-13 19,1 cm 57,2 cm 54,6 cm 5,98 kg
    60-1368-13A 19,1 cm 57,2 cm 54,6 cm 5,98 kg