MPS 602

Technische Daten

MPS 602
Video — VGA
Gain	Unity
Bandwidth	170 MHz (-3 dB)
Crosstalk	-50 dB @ 10 MHz, -30 dB @ 100 MHz
Video — HDMI and DTP
Maximum data rate	6.75 Gbps (2.25 Gbps per color)
Maximum pixel clock	165 MHz
Resolution	1920x1200 @ 60 Hz or 1080p @ 60 Hz, and 2K
Formats	RGB and YCbCr digital video
Standards	DVI 1.0, HDMI 1.3, HDCP 1.1, CEA-861E
Video input
Number/signal type
VGA inputs	2 VGA-QXGA, RGBHV, RGBS
HDMI inputs	3 HDMI (or single link DVI-D, with appropriate DVI-HDMI adapters)
DTP input	1 DTP 330 input
Connectors
VGA inputs	2 female 15-pin HD
HDMI inputs	3 female HDMI, type A
DTP input	1 RJ-45 female
Nominal level
VGA inputs	0.7 Vp-p for RGB
Minimum/maximum levels
VGA inputs	Analog 0.3 V to 1.5 Vp-p with no offset
Impedance	75 ohms
Horizontal frequency	15 kHz to 145 kHz
Vertical frequency	30 Hz to 170 Hz
Return loss	<-40 dB @ 5 MHz
Video output
Number/signal type
Local VGA output	1 VGA-QXGA, RGBHV, RGBS
HDMI outputs	1 HDMI (or single link DVI-D)
DTP output	1 DTP 330 output
DTP signal
Transmission distance	up to 330' (100 m) using shielded twisted pair (STP) or XTP DTP 24 cable
Cable requirements	Solid conductor, 24 AWG or better
Cable recommendations	400 MHz bandwidth, STP (shielded twisted pair)
NOTE     Extron XTP DTP 24 shielded twisted pair cable is strongly recommended for optimal performance.
Connectors
Local VGA output	1 female 15-pin HD
HDMI outputs	1 female HDMI type A
DTP output	1 RJ-45 jack
NOTE     Outputs are selectable from either the HDMI output or DTP output. The switcher does not output to both connectors simultaneously. Analog RGB inputs are digitized for output from either the HDMI or DTP output.
Nominal level
VGA outputs	0.7 Vp-p for RGB
Minimum/maximum levels
VGA outputs	Analog, 0.3 Vp-p to 1.5 Vp-p
Impedance	75 ohms
Return loss (VGA output)	<-40 dB @ 5 MHz
DC offset (max. allowable, VGA output)	±5 mV with input at 0 offset
Sync — VGA Inputs Only
Input type	RGBHV, RGBS
Local VGA output	RGBHV, RGBS
Input level	1.9 Vp-p to 5.0 Vp-p
Output level	TTL: 5.0 Vp-p (unterminated) for RGBHV, RGBS
Input impedance	510 ohms
Output impedance	75 ohms
Max. input voltage	5.0 Vp-p
Max. propagation delay	30 ns
Max. rise/fall time	4.2 ns
Polarity	Positive or negative (follows input)
Audio — individual audio groups (VGA, HDMI)
Gain	Unbalanced output: 0 dB; balanced output: +6 dB
Frequency response	20 Hz to 20 kHz, ±0.5 dB
THD + Noise
MPS 602	0.01% @ 1 kHz at nominal level
MPS 602 SA/MA	<0.1% @ 1 kHz 3 dB below clipping
S/N
MPS 602	>90 dB at maximum output (unweighted)
MPS 602 SA/MA	>90 dB 20 Hz to 20 kHz, unweighted
Crosstalk	<-72 dB @ 1 kHz or below, <-45 dB @ 20 kHz
Stereo channel separation	>80 dB @ 1 kHz
CMRR	>60 dB @ 1 kHz
Audio input — (VGA, and HDMI video)
Number/signal type
VGA inputs	2 stereo, unbalanced/balanced
HDMI inputs	3 stereo, unbalanced/unbalanced, or 3 embedded digital audio from HDMI
DTP input	1 stereo, unbalanced analog 1 embedded digital audio from DTP
Embedded digital audio source formats	2-ch PCM
Connectors
VGA inputs	(2) 3.5 mm captive screw connectors, 5-pole
HDMI inputs	(3) 3.5 mm captive screw connectors, 5-pole 3 female HDMI type A
DTP input	1 female RJ-45 connector
Input impedance	>10k ohms unbalanced, 20k ohms balanced
Nominal level	+4 dBu balanced, -10 dBV unbalanced, configurable
Maximum level	+15.2 dBu, balanced, +9.2 dBu unbalanced
CMRR	>60 dB typical @ 1 kHz
Input gain adjustment	-18 dB to +24 dB, adjustable per input
NOTE     0 dBu = 0.775 Vrms, 0 dBV = 1 Vrms, 0 dBV ? 2 dBu
Audio output
Number/signal type	2 stereo, balanced/unbalanced (fixed and variable outputs) 1 DTP analog audio and 1 embedded digital audio on DTP signal 1 embedded digital audio on HDMI
Connectors	(2) 3.5 mm captive screw connectors, 5-pole 1 RJ-45 1 female HDMI type A
Impedance	50 ohms unbalanced, 100 ohms balanced
Gain error	±0.5 dB channel to channel
Nominal level when the main volume is set to default	-2 dBu (632 mVrms) balanced output
Maximum level	+15.2 dBu balanced, +9.2 dBV unbalanced
Talk-over (ducking) response time (typical)
Attack time	Instant
Release delay	5 seconds
Release time	1 second
Ducking level	0 dB to 30 dB, adjustable; default = +6 dB
Audio output — power amplifier
Number/signal type
MPS 602 SA	1 stereo (default) or 2 mono, 2 channels total
MPS 602 MA	1 mono, 70V line
Connector
MPS 602 SA	(1) 5 mm screw lock captive screw connector, 4-pole
MPS 602 MA	(1) 5 mm screw lock captive screw connector, 2-pole
Load impedance
MPS 602 SA	4 ohms minimum
MPS 602 MA	50 ohms minimum
Output power
MPS 602 SA	25 watts rms per channel, 8 ohms, 1 kHz, 0.1% THD 50 watts rms per channel, 4 ohms, 1 kHz, 0.1% THD
MPS 602 MA	100 watts rms 70V, 1 kHz, 0.1% THD
THD + Noise	0.1% @ 1 kHz, 3 dB below clipping
Amplifier type	Class D
Mic/line input
Number/signal type	1 mono balanced/unbalanced
Connector	(1) 3.5 mm captive screw connector
Impedance	10k ohms unbalanced, 20k ohms balanced
Nominal level	-60 dBV (1 mV), +4 dBu, -10 dBV, adjustable
Equivalent input noise	<-117 dBV (1.4 uVrms) when gain is set to 40 dB
Maximum level	+12 dBV (2 Vrms) when gain is set to 0 dB
CMRR	>60 dB typical @ 1 kHz
Input gain adjustment	-18 dB to +60 dB, 1 dB steps, adjustable per input
Microphone volume range	-66 dB to +12 dB
Microphone DC power	+48 VDC +10% phantom power, can be turned on or off
NOTE     Mic/line audio is not embedded on DTP analog audio output or digital embedded audio.
Communications — switcher
Serial control port	1 RS-232, 3.5 mm captive screw connector, 3-pole, rear panel
Baud rate and protocol	9600 baud, 8 data bits, 1 stop bit, no parity
Serial control pin configuration	2 = Tx, 3 = Rx, 5 = Gnd
USB control ports	1 front panel female mini USB B
USB standards	USB 2.0, high speed
Program control	Extron Simple Instruction Set (SIS™), Extron Product Configuration Software (PCS)
Communications — external device (pass-through, unidirectional or bidirectional)
NOTE     Protocol is mirrored between the connected DTP 230 endpoints and the "Over DTP" input and output ports. Signals from a control device pass into each "Over DTP" port, are embedded with the DTP signal, and sent to individual DTP 230 Tx or Rx endpoints for control of remote sink or source devices. The "Over DTP" ports are pass-through connections to DTP endpoints. There is no RS-232 or IR insertion from the MPS 602 control ports to the "Over DTP" ports.
Quantity/type	(2) RS-232 and IR via (2) 3.5 mm captive screw connectors, 5-pole
Serial control pass-through ports	(2) bidirectional RS-232
Input/DTP Tx	(1) RS-232 (1) 3.5 mm 5-pole captive screw connector (shared with IR port)
Output/DTP Rx	(1) RS-232 (1) 3.5 mm 5-pole captive screw connector (shared with IR port)
Baud rates	300 to 115200 baud
Protocol	8 or 7 data bits, 1 or 2 stop bits, no parity (default), even or odd parity
Serial control pin configuration	1 = Tx, 2 = Rx, 3 = Gnd
IR pass-through control ports	2 bidirectional TTL level (0 to 5 V) modulated infrared control from 30 kHz up to 60 kHz
Input/DTP Tx	(1) RS-232 (1) 3.5 mm captive screw connector, 5-pole (shared with RS-232 port)
Output/DTP Rx	(1) RS-232 (1) 3.5 mm captive screw connector, 5-pole (shared with RS-232 port)
IR control pin configuration	3 = Gnd, 4 = IR Tx, 5 = IR Rx
General
Power supply	Internal Input: 100-240 VAC, 50-60 Hz
Power consumption
MPS 602	Full load, 22 W
MPS 602 SA	Full load, amp at 1/8 power: 44 W
MPS 602 MA	Full load, amp at 1/8 power: 44 W
Remote power capability	Supports up to two endpoints (one DTP Tx, one DTP Rx)
Temperature/humidity	Storage -40 to +158 °F (-40 to +70 °C) / 10% to 90%, noncondensing Operating +32 to +122 °F (0 to +50 °C) / 10% to 90%, noncondensing
Cooling	Convection, vents on top and sides
Power consumption	22 watts
Thermal dissipation
MPS 602	Full load, 69 BTU/hr
MPS 602 SA	Full load, amp at 1/8 power: 102 BTU/hr
MPS 602 MA	Full load, amp at 1/8 power: 102 BTU/hr
Mounting
Rack mount	Yes, with included brackets
Enclosure type	Metal
Enclosure dimensions	1.75" H x 17.4" W x 8.5" D (1U high, full rack wide) 4.4 cm H x 43.2 cm W x 21.6 cm D (Depth excludes connectors and knobs. Width excludes rack ears.)
Product weight	7.0 lbs (3.2 kg)
Shipping weight	10 lbs (5 kg)
Vibration	ISTA 1A in carton (International Safe Transit Association)
Regulatory compliance
Safety	CE, c-UL, UL
EMI/EMC	CE, C-tick, ICES, FCC Class A, VCCI, ICES
Environmental	Complies with the appropriate requirements of RoHS, WEEE
Product warranty	3 years parts and labor
Everlast power supply warranty	7 years parts and labor
NOTE     All nominal levels are at ±10%.
NOTE     Specifications are subject to change without notice.
(8.1-070115-D8)

Versand-Abmessung und -Gewicht
Teilenummer	Höhe	Breite	Tiefe	Gewicht
60-1313-51	11,4 cm	54,6 cm	36,2 cm	2,63 kg
60-1314-51	11,4 cm	54,6 cm	36,2 cm	3,04 kg
60-1315-51	11,4 cm	54,6 cm	36,2 cm	3,04 kg