XTP FT HD 4K

Technische Daten

XTP FT HD 4K
specification
Frame rate 1	24, 25, 30, 50, or 60 fps
Chroma sampling 1	4:4:4, 4:2:2, or 4:2:0
Color bit depth 1	8 bits per color
Signal type	DisplayPort 1.1, DVI 1.0, HDMI 1.4a, HDCP 1.4
Max. video data rate	8.91 Gbps (2.97 Gbps per color)
NOTE     1Subject to the maximum data rate limit. Use our calculator at www.extron.com/4Kdatarate to determine video parameters supported by this data rate.
NOTE     The XTP FT HD 4K transmitter can be used with XTP receivers, with a fiber optic cable linking the transmitter and receiver, or with other Extron XTP products.
NOTE     These transmitters are class 1 laser products. They meet the safety regulations of IEC 60825-1.
Video
Gain	Unity
Resolution range	Up to 2560x1600 @ 60 Hz* or 4K (4096x2160) @ 24 Hz, UHD (3840x2160) @ 30 Hz, UHD @ 60 Hz with 4:2:0 chroma subsampling * reduced blanking
Signal type	Single-link HDMI (or DVI-D or DisplayPort)
Color bit depth	8, 10, or 12 bits — subject to the maximum data rate limit
Maximum data rate	8.91 Gbps (2.97 Gbps per color)
Maximum pixel clock	300 MHz (600 MHz for 4K rates with 4:2:0 chroma subsampling)
Formats	RGB and YCbCr digital video
Standards	DisplayPort 1.1, DVI 1.0, HDMI 1.4a, HDCP 1.4
Video input and loop-through
Number/signal type	1 single link HDMI (or DVI-D or DisplayPort) input 1 single link HDMI (or DVI-D) loop-through
Connectors	2 female HDMI type A: 1 input, 1 loop-through
Optical fiber interconnection between transmitter and receiver
Number/signal type	1 set of proprietary signals
Connectors	1 LC fiber connector
Operating distance
NOTE     Operating distance is approximate. These are typical maximum distances that may vary depending on factors such as fiber type, fiber bandwidth, connector splicing, losses, modal or chromatic dispersion, environmental factors, and kinks.
Singlemode	10 km (6.21 miles) with singlemode cable
Multimode	400 m (1312') with 50 µm OM3 2000 MHz bandwidth laser optimzed multimode cable 700 m (2297') with 50 µm OM4 4700 MHz bandwidth laser optimzed multimode cable
NOTE     Multimode units are compatible with OM1 and OM2 multimode cables, but at reduced operating distances.
Nominal peak wavelength
Singlemode	1490 nm, 1550 nm, 1310 nm
Multimode	850 nm, 980 nm, 780 nm
Data rate	8.5 Gbps
Transmission power
Singlemode	-6 dBm, typical
Multimode	-5 dBm, typical
Maximum receiver sensitivity
Singlemode	-15 dBm, typical
Multimode	-13 dBm, typical
Optical loss budget
Singlemode	9 dB, maximum
Multimode	8 dB, maximum
Audio
Gain	Unbalanced output: 0 dB; balanced output: +6 dB
Frequency response	20 Hz to 20 kHz, ±0.5 dB
THD + Noise	<0.1%, 20 Hz - 20 kHz at nominal level
S/N	>90 dB, at maximum balanced output (unweighted)
Crosstalk	?-80 dB @ 1 kHz, fully loaded
Stereo channel separation	>80 dB @ 1 kHz
Sampling rates	32 kHz, 44.1 kHz, 48 kHz, 96 kHz, 192 kHz
Bit depths	16, 20, 24 bit
Audio input
Number/signal type	1 analog stereo, balanced/unbalanced or 1 digital audio, de-embedded from HDMI
Connectors	(1) 3.5 mm captive screw connector, 5 pole 1 female HDMI type A (shared with video input)
Source formats	LPCM up to 7.1/24-bit/192 kHz, Dolby Atmos™, Dolby TrueHD, Dolby Digital Plus™, Dolby Digital EX, Dolby Digital 5.1, Dolby Digital 2/0 Surround, Dolby Digital 2/0, DTS-HD Master Audio™, DTS-HD, DTS-ES Discrete 6.1, DTS-ES Matrix 6.1, DTS Digital Surround 5.1, DTS 2 Channel, analog stereo
Impedance	10k ohms, unbalanced, 20k ohms balanced
Nominal level	+4 dBu (1.23 mVrms) balanced, -10 dBV (316 mVrms) unbalanced
Maximum level	+21 dBu balanced, +15 dBu unbalanced
Input gain adjustment	-18 dB to +24 dB, 1 dB steps, adjustable
NOTE     0 dBu = 0.775 Vrms, 0 dBV = 1 Vrms, 0 dBV ? 2 dBu
Communications — transmitter
USB control ports	1 front panel female mini USB B
USB standards	USB 2.0, low speed
Program control	Extron control/configuration program for Windows® Extron Simple Instruction Set (SIS™)
Communications — external device (pass-through, unidirectional or bidirectional)
Serial control pass-through port	RS-232 (+5 V) via a (1) 3.5 mm, 5 pole captive screw connector (uses 3 poles) (connector is shared with the IR control port)
Baud rates	Up to 115200 baud
Protocol	Data bits = 5 - 8 Stop bits = 1 or 2 Parity = odd, even, none Flow control = XON, XOFF, none
Serial control pin configuration	1 = Tx, 2 = Rx, 3 = GND
IR control port	(1) 3.5 mm, captive screw connector, 5 pole (uses 3 poles) (connector is shared with the RS-232 control port) TTL level (0 to 5 V) modulated infrared control from 30 kHz up to 56 kHz
IR control pin configuration	3 = GND, 4 = IR Tx, 5 = IR Rx
Ethernet pass-through port	1 female RJ-45 connector
Ethernet data rate	10/100Base-T, full duplex with autodetect
General
Power supply	External Input: 100-240 VAC, 50-60 Hz Output: 12 VDC, 1.5 A, 18 watts
Power consumption
Device	8.1 watts
Device and power supply	10 watts
Temperature/humidity	Storage: -40 to +158 °F (-40 to +70 °C) / 10% to 90%, noncondensing Operating: +32 to +122 °F (0 to +50 °C) / 10% to 90%, noncondensing
Cooling	Convection, vents
Thermal dissipation
Device	26.2 BTU/hr
Device and power supply	32.8 BTU/hr
Mounting
Rack mount	Yes, with optional 1U high rack shelf
Furniture mount	Yes, with optional under-desk mounting kit
Enclosure type	Metal
Enclosure dimensions	1.0" H x 8.75" W x 6.0" D (half rack wide) (2.5 cm H x 22.2 cm W x 15.2 cm D) (Depth excludes connectors.)
Product weight	1.6 lbs (0.7 kg)
Vibration	ISTA 1A in carton (International Safe Transit Association)
Regulatory compliance	CE, c-UL, UL, IEC 60825-1, C-tick, FCC Class A, ICES, VCCI Complies with the appropriate requirements of RoHS and WEEE.
Product warranty	3 years parts and labor
Everlast power supply warranty	7 years parts and labor
NOTE     All nominal levels are at ±10%.
NOTE     Specifications are subject to change without notice.
(4442-D8)

Versand-Abmessung und -Gewicht
Teilenummer	Höhe	Breite	Tiefe	Gewicht
60-1276-11	10,2 cm	27,2 cm	23,5 cm	1,26 kg
60-1276-12	10,2 cm	27,2 cm	23,5 cm	1,26 kg