XTP T FB 202

Technische Daten

XTP T FB 202
NOTE     The XTP switcher can be used with other Extron XTP products, with twisted pair cables connecting the units.
NOTE     *Appropriate DVI-D to HDMI or DisplayPort to HDMI cables or adapters are required for DVI or DisplayPort signal input.
Video
Gain	Unity
Resolution range
Digital	Up to 1920x1200*, 2K, or 1080p (HDTV) * reduced blanking
Analog	Up to 1920x1200* or 1080p (HDTV) * reduced blanking
Signal type	Single-link HDMI (or DVI-D*)
Digital video	RGB digital video (DVI and HDMI standards) or Y, Cr, Cb digital component video (HDMI), actively buffered (supports all single-link DVI (if using an optional adapter) and HDMI standards from 640x480 @ 60 Hz to 1900x1200 @ 60 Hz)
EDID and DDC	Supports Extended Display Identification Data (EDID) and Display Data Channel (DDC) data using DVI and HDMI standards.  EDID and DDC signals are actively buffered.
HDCP	Compliant with High-bandwidth Digital Content Protection (HDCP) using DVI and HDMI standards
HPD	Supports hot plug detection (HPD) of display as a pass-through signal.
Maximum data rate	6.75 Gbps (2.25 Gbps per color)
Maximum pixel clock	165 MHz
Formats	RGB and YCbCr digital video
Standards	DVI 1.0, HDMI, HDCP 1.1
Video input
Number/signal type	1 analog RGBHV 1 single link HDMI (DVI-D or DisplayPort*) input
Connectors	1 female 15-pin HD 1 female HDMI type A
Nominal level	0.7 Vp-p for RGB
Minimum/maximum levels	0.3 V to 1.45 V p-p
Impedance	75 ohms
Horizontal frequency	30 kHz to 100 kHz
Vertical frequency	24 Hz to 120 Hz
Interconnection between transmitter and receiver
Connectors	1 female RJ-45 per unit
Termination standards	TIA/EIA T568B
Signal transmission distance	330' (100 m) using shielded twisted pair or XTP DTP 24 cable
Cable requirements	Solid conductor, 24 AWG or better
Cable recommendations	400 MHz bandwidth, STP (Shielded Twisted Pair)
NOTE     Extron XTP DTP 24 shielded twisted pair cable is stongly recommended for optimal performance.
Audio
Gain
Range	-18 dB to +24 dB
Default	Unbalanced output: 0 dB; balanced output +6 dB
Frequency response	20 Hz to 20 kHz, ±0.05 dB
THD + Noise	0.01% @ 1 kHz at nominal level
S/N	>90 dB, at maximum output, balanced (unweighted)
Crosstalk	<-45 dB @ 20 kHz, -72 dB @ 1 kHz or below
Stereo channel separation	>80 dB @ 20 Hz to 20 kHz
Sampling rates	32 kHz, 44.1 kHz, 48 kHz, 96 kHz, 192 kHz
Bit depths	16, 20, 24 bit
Audio input
Number/signal type	1 analog stereo, unbalanced or 1 digital audio, embedded from HDMI
Connectors	1 female 3.5 mm mini audio jack 1 female HDMI type A (shared with video input)
Source formats	LPCM up to 7.1/24-bit/192 kHz, Dolby TrueHD, Dolby Digital Plus, Dolby Digital EX, Dolby Digital 5.1, Dolby Digital 2/0 Surround, Dolby Digital 2/0, DTS-HD Master Audio, DTS-HD, DTS-ES Discrete 6.1, DTS-ES Matrix 6.1, DTS Digital Surround 5.1, DTS 2 Channel
Impedance	>10k ohms, unbalanced, DC coupled
Nominal level	+4 dBu (1.23 mVrms) balanced or -10 dBV (316 mVrms) unbalanced
Maximum level	+7 dBv unbalanced
NOTE     0 dBu = 0.775 Vrms, 0 dBV = 1 Vrms, 0 dBV ? 2 dBu
Communications — switcher
Serial control port	1 bidirectional RS-232: 1 rear panel 3.5 mm captive screw connector, 3 pole
Baud rate and protocol	9600 (default) to 115200 baud, 8 data bits, 1 stop bit, no parity
Serial control pin configuration	1 = Tx, 2 = Rx, 3 = GND
USB control ports	1 front panel female mini USB B
USB standards	USB 2.0, low speed
Program control	Extron control/configuration program for Windows® Extron Simple Instruction Set (SIS™)
Communications — external device (pass-through, unidirectional or bidirectional)
Serial control port input/output	RS-232 (±5 V) via (1) 3.5 mm, 5 pole captive screw connector (uses 3 poles) (connector is shared with IR control port)
Serial control port output/input	1 set of proprietary signals on a female RJ-45 jack
Baud rates	Up to 115200 baud
Protocol	Data bits = 5 - 8 Stop bits = 1 or 2 Parity = odd, even, none Flow control = XON, XOFF, none
Serial control pin configuration	1 = Tx, 2 = Rx, 3 = GND
Ethernet pass-through port	1 female RJ-45 connector
Ethernet data rate	10/100Base-T, half/full duplex with autodetect
IR control port	(1) 3.5 mm, captive screw connector, 5 pole (connector is shared with RS-232 control port) TTL level (0 to 5 V) modulated infrared control from 30 kHz up to 40 kHz
IR control pin configuration	3 = GND, 4 = IR Tx, 5 = IR Rx
General
Power supply	External Input: 100 to 240 VAC, 50-60 Hz Output: 12 VDC, 1.5 A, 18 watts
Power consumption
Device	10.4 watts, 12 VDC
Device and power supply	12.9 watts, 100-240 VAC, 50-60 Hz
NOTE     Each XTP switcher, transmitter, receiver can be powered either locally by an external power supply or remotely using an optional power injector.
Temperature/humidity	Storage: -40 to +158 °F (-40 to +70 °C) / 10% to 90%, noncondensing Operating: +32 to +104 °F (0 to +40 °C) / 10% to 90%, noncondensing
Cooling	Convection, no vents
Thermal dissipation
Device	33.1 BTU/hr
Device and power supply	41.8 BTU/hr
Mounting
Floor box mount	Ackermann GB3/OBO Betterman floor box, MK Electric CableLink Plus Single Pan floor box, MK Electric CableLink Plus Modular floor box, ElectraPlan floor box, and PUK floor box mountable
NOTE     See the XTP T FB 202 User Guide for mounting considerations.
Enclosure type	Metal
Enclosure dimensions	2.3" H x 2.8" W x 5.2" D* (5.9 cm H x 7.2 cm W x 13.2 cm D) (Dimensions exclude connectors) * Depth is 6.1" (15.5 cm) including mounting tabs
Product weight	1.4 lbs (0.6 kg)
Shipping weight	4 lbs (2 kg)
Vibration	ISTA 1A in carton (International Safe Transit Association)
Regulatory compliance	CE**, c-UL, UL, C-tick, FCC Class A**, ICES, VCCI Complies with the appropriate requirements of RoHS and WEEE.
NOTE     **CE and FCC testing is conducted with STP (shielded twisted pair) cable.
Product warranty	3 years parts and labor
Everlast power supply warranty	7 years parts and labor
NOTE     All nominal levels are at ±10%.
NOTE     Specifications are subject to change without notice.
(4449-D6)

Versand-Abmessung und -Gewicht
Teilenummer	Höhe	Breite	Tiefe	Gewicht
60-1383-12	7,5 cm	26,7 cm	19,1 cm	1,48 kg